BootStrap - Revision history

FabienM: /* Introduction */

2020-05-06T14:31:18Z

‎Introduction

2018-11-27T14:55:44Z

‎Usage

2018-10-01T14:12:13Z

‎Introduction

2016-11-09T14:08:42Z

‎Usage

2016-09-09T14:13:26Z

‎Usage

2016-09-09T13:19:10Z

2016-09-09T13:18:33Z

‎Introduction

2015-04-24T12:04:35Z

‎Usage

2015-04-03T13:08:08Z

‎Introduction

2014-12-24T11:35:34Z

‎Introduction

@@ Line 21: / Line 21: @@
 || [[Image:bootstrap_jumper_apf51.jpg|thumb|right|On the [[APF51Dev]] (Boot)]]
 || [[Image:bootstrap_jumper_apf28dev.jpg|thumb|right|On the [[APF28Dev]]]]
-|| [[Image:bootstrap_jumper_apf6dev.jpg|thumb|right|On the [[APF6Dev]] (BOOT0 & BOOT1)]]
+|| [[Image:bootstrap_jumper_apf6dev.jpg|thumb|right|On the [[APF6Dev]] (off BOOT0 & on BOOT1)]]
 || [[Image:bootstrap_jumper_opos6uldev.jpg|thumb|right|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]
 |----------------

@@ Line 57: / Line 57: @@
 </pre>
-||
+||<pre class="host">
 ||
@@ Line 119: / Line 127: @@
 ||<pre class="host">
-run flash_uboot
+successful operation completion
-device 0 offset 0x0, size 0xa0000
+SDRAM INIT1 APF SDRAM INIT2 APF
-nand_unlock: start: 00000000, length: 655360!
+Transfering:
 NAND flash successfully unlocked
-NAND erase: device 0 offset 0x0, size 0xa0000
+NAND erase.part: device 0 offset 0x0, size 0xa0000
 OK
-NAND write: device 0 offset 0x0, size 0xa0000
+NAND write: device 0 offset 0x0, size 0x5cc1c
 bytes written: OK
 NAND flash successfully locked
-device 0 offset 0xa0000, size 0x7f60000
+device 0 offset 0xa0000, size 0xff60000
-nand_unlock: start: 000a0000, length: 133562368!
+nand_unlock: start: 000a0000, length: 267780096!
 NAND flash successfully unlocked
 Flashing of uboot succeed
-BIOS>uBoot successfully recovered !
+BIOS>U-Boot successfully recovered !
 </pre>
 ||

@@ Line 22: / Line 22: @@
 || [[Image:bootstrap_jumper_apf28dev.jpg|thumb|right|On the [[APF28Dev]]]]
 || [[Image:bootstrap_jumper_apf6dev.jpg|thumb|right|On the [[APF6Dev]] (BOOT0 & BOOT1)]]
-|| [[Image:bootstrap_jumper_opos6uldev.jpg|thumb|right|On the [[OPOS6ULDev]] (BOOT0 & BOOT1)]]
+|| [[Image:bootstrap_jumper_opos6uldev.jpg|thumb|right|On the [[OPOS6UL]]+[[OPOS6ULDev]] (BOOT0 & BOOT1). Do not work with OPOS6ULNANO !!!]]
 |----------------
 |}

@@ Line 29: / Line 29: @@
 ==Usage==
 * '''Quit all Kermit/Minicom/GTKTerm/Hyperterminal sessions connected to the board through Serial Port.'''
-*Go inside the ''software/uboot_recover/'' directory and launch (sudo usage is only required on [[APF28]], [[APF51]] and [[APF6]]):
+*Go inside the ''software/uboot_recover/'' directory and launch (sudo usage is required on [[APF28]], [[APF51]], [[APF6]] and [[OPOS6UL]]):
 <pre class="host">
 $ cd software/uboot_recover/
-$ sudo python apfXX_recover.py        (XX depends on the version of your board (ie: 9328, 27, 28, 51 or 6))
+$ sudo python xxxx_recover.py        (xxxx depends on the version of your board (ie: apf9328, apf27, apf28, apf51, apf6 or opos6ul))
 </pre>

@@ Line 40: / Line 40: @@
 {| border="1" cellpadding="5" cellspacing="0" summary="Tool instructions"
 |- style="background:#efefef;"
-! '''APF9328''' || '''APF27''' || '''APF51''' || '''APF28''' || '''APF6'''
+! '''APF9328''' || '''APF27''' || '''APF51''' || '''APF28''' || '''APF6''' || '''OPOS6UL''
 |----------------
 ||
@@ Line 78: / Line 78: @@
 --- Enter serial port number or device name to use for console (/dev/ttyUSB0 under Linux (default) or COMx under Window$):
 </pre>
 |----------------
@@ Line 88: / Line 104: @@
 {| border="1" cellpadding="5" cellspacing="0" summary="Recovery final messages"
 |- style="background:#efefef;"
-! '''APF9328''' || '''APF27''' || '''APF51''' || '''APF28''' || '''APF6'''
+! '''APF9328''' || '''APF27''' || '''APF51''' || '''APF28''' || '''APF6''' || '''OPOS6UL'''
 |----------------
 ||<pre class="host">
@@ Line 237: / Line 253: @@
 --- Now you can remove miniUSB OTG cable and put the jumper back on BOOT0 pin. Your board is running...
 </pre>
 |----------------
 |}

@@ Line 10: / Line 10: @@
 </pre>
-This utility communicates with the i.MX(L/27/28/51/6) processor while in ''bootstrap mode'' (See i.MX(L/27/28/51/6) Reference Manual for more informations).
+This utility communicates with the i.MX(L/27/28/51/6/6UL) processor while in ''bootstrap mode'' (See i.MX(L/27/28/51/6/6UL) Reference Manual for more informations).
 * To enter the bootstrap mode, you have to put the bootstrap jumper and reset your Armadeus board: <br>

← Older revision		Revision as of 12:04, 24 April 2015
Line 57:		Line 57:

	\|\|		\|\|
−	~~The size of the SDRAM has to be indicated. Default value is 64Mo.~~
−	~~<pre class="host">~~
−	~~TBDL~~

−	~~</pre>~~
	\|\|		\|\|

@@ Line 15: / Line 15: @@
 {|border=0 summary="Photos"
 |----------------
-| [[Image:bootstrap_jumper.jpg|thumb|left|On the [[APF9328DevLight]]]] || [[Image:bootstrap_jumper_devfull.jpg|thumb|center|On the [[APF9328DevFull]] (Boot)]] || [[Image:bootstrap_jumper_apf27.jpg|thumb|right|On the [[APF27Dev]] (J12)]]
+| [[Image:bootstrap_jumper.jpg|thumb|left|On the [[APF9328DevLight]]]]
 || [[Image:bootstrap_jumper_apf51.jpg|thumb|right|On the [[APF51Dev]] (Boot)]]
 || [[Image:bootstrap_jumper_apf28dev.jpg|thumb|right|On the [[APF28Dev]]]]