GPS - Revision history

JulienB at 12:50, 29 March 2017

2017-03-29T12:50:34Z

2014-10-27T10:10:54Z

Add APF6Dev explanation.

2013-09-04T16:00:42Z

‎Configuration

2012-11-19T07:31:57Z

‎Usage

2011-12-12T20:04:31Z

2011-12-12T20:02:18Z

‎Usage

2011-12-12T19:59:33Z

‎Usage

2011-12-12T19:59:10Z

‎Configuration

2011-10-27T12:37:06Z

‎Usage

2011-10-24T14:03:19Z

‎APF27 Wireless (APW)

@@ Line 16: / Line 16: @@
 ===USB modules===
 These modules are mostly serial one with a RS232 <-> USB converter. None were tested yet.
 == APF51Dev ==

@@ Line 21: / Line 21: @@
 * Should be done by default; if not here is how to:
 <pre class="host">
-$ make linux26-menuconfig
+$ make linux-menuconfig
 </pre>

@@ Line 57: / Line 57: @@
 </pre>
 {{Note| depending on GPS firmware '''9600 bauds''' may be the default speed instead of 38400 bauds}}
-Then for a 38400 bauds communication.
+Then for a 38400 bauds communication:
 <pre class="apf">
 # export GPS_PORT=/dev/ttyS1
 # stty -F $GPS_PORT raw -echo -echoe -echok 38400
 </pre>

@@ Line 17: / Line 17: @@
 These modules are mostly serial one with a RS232 <-> USB converter. None were tested yet.
-=== APF51Dev ===
+== APF51Dev ==
 ===Configuration===
 * Should be done by default; if not here is how to:
@@ Line 63: / Line 63: @@
 </pre>
-=== APF27 Wireless (APW)===
+== APF27 Wireless (APW)==
 * Be sure to have correctly choosen the GPS option [[Wireless_extension_board#Linux_configuration|while configuring you Linux kernel for the APW]]. This will autoselect and activate corresponding serial port. Reflash your Linux kernel.
 * Be sure that J3 jumper (near SIM card socket) is plugged in
@@ Line 82: / Line 82: @@
 </pre>
-=== APF9328 ===
+== APF9328 ==
 * Configure Serial port 1 of your APF9328 (4800 bauds 8N1):
 <pre class="apf">

@@ Line 51: / Line 51: @@
 </pre>
 * Configure serial port:
-If the /dev/ttyS[0-1] files don't exist, create it/them with ''mknod'' :
+If the ''/dev/ttyS[0-1]'' device files are not created automatically, then create it/them with ''mknod'' :
 <pre class="apf">
 # mknod /dev/ttyS0 c 4 64

@@ Line 35: / Line 35: @@
 ===Usage===
-* Don't forget to put "Wireless" jumper J42 on your [[APF51Dev]] (near microSD connector) AND power on FPGA Bank 3 (with corresponding jumper J39).
+* Don't forget to put "Wireless" jumper J42 on your [[APF51Dev]] (near microSD connector) '''AND''' to power on FPGA Bank 3 (with corresponding jumper J39).
 * On APF51Dev, optionnal GPS module (like GSM/3G) is accessed through a serial port synthetized in APF51's FPGA. So it has to be "loaded" first. (Needed dual UARTs FPGA firmware can be found under armadeus-4.0 distribution in ''firmware/pod_scripts'' directory, with the [[POD]] script needed to regenerate it, and is by default installed in rootfs).
 <pre class="apf">

@@ Line 64: / Line 64: @@
 * Be sure that J3 jumper (near SIM card socket) is plugged in
 * Configure GPS serial port (4 for Linux == UART5 for i.MX) of your APF27 (raw, no echo, 38400 bauds 8N1):
 <pre class="apf">
 # stty -F /dev/ttySMX4 raw -echo -echoe -echok 38400