GSM/GPRS - Revision history

JulienB: /* Introduction */

2023-08-17T13:23:31Z

‎Introduction

2023-08-17T13:21:35Z

2023-08-17T13:20:24Z

‎APF6Dev

2018-01-02T15:57:48Z

‎Sending AT commands "manually"

2014-12-24T11:47:05Z

‎Introduction

2014-10-10T12:28:18Z

Add APF6Dev explanation.

2013-09-04T16:13:23Z

‎PPP installation (done by default on APF51)

2013-09-04T16:13:06Z

‎Linux configuration (APF27Dev only)

2013-06-28T15:34:25Z

‎Build SMS Server Tools3

2013-06-28T14:59:08Z

‎Build SMS Server Tools3

@@ Line 7: / Line 7: @@
 * GSM/3G MODEM of the [[APF6Dev]] is connected to the UART3 of the i.MX6 processor.
 They are all using a Sagem's Hilo module. Hilo AT commands can be found [http://support.sagemcom.com/site/livret/URD1_OTL_5725_1_008_72807_-_AT_Command_Set_for_SAGEMCOM_Modules__Ed_14_06_dated_11_May_2012.pdf here]
 ==Linux configuration (APF27Dev only)==

← Older revision		Revision as of 13:21, 17 August 2023
Line 1:		Line 1:
−	This page will summarize informations to use the GSM/GPRS/3G module of the [[Wireless_extension_board\|APF27Wireless board]], [[APF51Dev]] (optional) ~~and~~ the [[APF6Dev]] (optional).	+	This page will summarize informations to use the GSM/GPRS/3G module of the [[Wireless_extension_board\|APF27Wireless board]], [[APF51Dev]] (optional), the [[APF6Dev]] (optional) or the RPi compatible Hats connected to OPOSxxDev RPi connector.

	==Introduction==		==Introduction==

@@ Line 97: / Line 97: @@
 <pre class="apf">
 # export GSM_DEVICE=/dev/ttymxc2
 # stty -F $GSM_DEVICE -echo -echoe -echok 115200
 </pre>

@@ Line 102: / Line 102: @@
 ==Basic Usage==
 ===Sending AT commands "manually"===
-* Sending AT commands with ''minicom'' utility (one of the command coming with [[busybox]]):
+* Sending AT commands with ''minicom/microcom'' utility (one of the command coming with [[busybox]]):
-{{Note|minicom seem to be remove use microcom instead}}
+{{Note|minicom has been removed in recent BSP, so use microcom instead}}
 <pre class="apf">
-# minicom $GSM_DEVICE
+# microcom $GSM_DEVICE
 </pre>
-( To exit ''minocom'' you will have to type '''<CTRL-x>''' )
+( To exit ''microcom'' you will have to type '''<CTRL-x>''' )
 * Check module presence:
 <pre class="apf">

@@ Line 5: / Line 5: @@
 * GSM MODEM of the [[Wireless_extension_board|APF27Wireless extension board (APW)]] is connected to the UART2 (/dev/ttySMX1) of the [[APF27]].
 * GSM/3G MODEM of the [[APF51Dev]] is connected to the i.MX processor through an UART implemented in the FPGA. So the corresponding bitfile has to loaded before trying to access the MODEM.
-* GSM/3G MODEM of the [[APF51Dev]] is connected to the UART3 of the i.MX6 processor.
+* GSM/3G MODEM of the [[APF6Dev]] is connected to the UART3 of the i.MX6 processor.
 They are all using a Sagem's Hilo module. Hilo AT commands can be found [http://support.sagemcom.com/site/livret/URD1_OTL_5725_1_008_72807_-_AT_Command_Set_for_SAGEMCOM_Modules__Ed_14_06_dated_11_May_2012.pdf here]

@@ Line 1: / Line 1: @@
-This page will summarize informations to use the GSM/GPRS/3G module of the [[Wireless_extension_board|APF27Wireless board]] and the [[APF51Dev]] (optional).
+This page will summarize informations to use the GSM/GPRS/3G module of the [[Wireless_extension_board|APF27Wireless board]], [[APF51Dev]] (optional) and the [[APF6Dev]] (optional).
 ==Introduction==
@@ Line 5: / Line 5: @@
 * GSM MODEM of the [[Wireless_extension_board|APF27Wireless extension board (APW)]] is connected to the UART2 (/dev/ttySMX1) of the [[APF27]].
 * GSM/3G MODEM of the [[APF51Dev]] is connected to the i.MX processor through an UART implemented in the FPGA. So the corresponding bitfile has to loaded before trying to access the MODEM.
-Both are using a Sagem's Hilo module. Hilo AT commands can be found [http://www.libelium.com/tienda/catalog/images/arduino/AT_Commands.pdf here]
+* GSM/3G MODEM of the [[APF51Dev]] is connected to the UART3 of the i.MX6 processor.
 ==Linux configuration (APF27Dev only)==
@@ Line 74: / Line 75: @@
 # export GSM_DEVICE=/dev/ttyS0
 # stty -F $GSM_DEVICE -echo -echoe -echok 115200 crtscts
 </pre>

@@ Line 218: / Line 218: @@
 ===PPP installation (done by default on APF51)===
 <pre class="host">
-$ make linux26-menuconfig
+$ make linux-menuconfig
 </pre>
@@ Line 248: / Line 248: @@
 <pre class="host">
-$ make linux26 && make
+$ make linux && make
 </pre>

@@ Line 408: / Line 408: @@
      Networking applications  --->
          [*] smstools3
 </pre>
 <pre class="host">

@@ Line 406: / Line 406: @@
 <pre class="config">
 Package Selection for the target  --->
-     Hardware handling  --->
+     Networking applications  --->
-         [*] SMS Server Tools3
+         [*] smstools3
 </pre>
 <pre class="host">