U-Boot communication quick check - Revision history

JulienB: /* U-Boot communication quick check */

2011-05-04T14:46:47Z

‎U-Boot communication quick check

JulienB: /* U-Boot communication quick check */

2011-05-04T14:06:21Z

‎U-Boot communication quick check

JulienB: /* U-Boot communication quick check */

2011-03-03T15:00:57Z

‎U-Boot communication quick check

JulienB at 08:49, 3 March 2009

2009-03-03T08:49:43Z

Jorasse: /* U-Boot communication quick check */

2009-03-02T23:03:35Z

‎U-Boot communication quick check

JulienB: New page: ==U-Boot communication quick check== * Verify that your RS232 cable is correctly connected * The bootstrap jumper must be removed * Start the RS232 terminal on t...

2009-03-02T16:18:36Z

New page: ==U-Boot communication quick check== * Verify that your RS232 cable is correctly connected * The bootstrap jumper must be removed * Start the RS232 terminal on t...

New page

==U-Boot communication quick check==
* Verify that your RS232 cable is correctly connected
* The [[BootStrap#Introduction|bootstrap jumper]] must be removed
* Start the RS232 terminal on the Host side (115200 bauds 8N1)
* Reset the board
* U-Boot must start

[[Linux_start_screenshot | Here is a screenshot]] of what you will see on your Terminal emulator during the Linux boot.

@@ Line 2: / Line 2: @@
 * Verify that your RS232 cable is correctly connected
 * The [[BootStrap#Introduction|bootstrap jumper]] '''must be removed''' as shown on these photos:
-  [[Image:bootstrap_jumper.jpg|On the [[APF9328DevLight]]]]  [[Image:bootstrap_jumper_devfull.jpg|On the [[APF9328DevFull]]]]  [[Image:bootstrap_jumper_apf27.jpg|On the [[APF27Dev]]]] [[Image:bootstrap_jumper_apf51.jpg|On the [[APF51Dev]]]]
+  [[Image:bootstrap_jumper.jpg|On the [[APF9328DevLight]]|200px]]  [[Image:bootstrap_jumper_devfull.jpg|On the [[APF9328DevFull]]|200px]]  [[Image:bootstrap_jumper_apf27.jpg|On the [[APF27Dev]]|200px]] [[Image:bootstrap_jumper_apf51.jpg|On the [[APF51Dev]]|200px]]
 * Start the RS232 terminal on the Host side (115200 bauds 8N1)

@@ Line 2: / Line 2: @@
 * Verify that your RS232 cable is correctly connected
 * The [[BootStrap#Introduction|bootstrap jumper]] '''must be removed''' as shown on these photos:
-  [[Image:bootstrap_jumper.jpg|On the [[APF9328DevLight]]]]  [[Image:bootstrap_jumper_devfull.jpg|On the [[APF9328DevFull]]]]  [[Image:bootstrap_jumper_apf27.jpg|On the [[APF27Dev]]]]
+  [[Image:bootstrap_jumper.jpg|On the [[APF9328DevLight]]]]  [[Image:bootstrap_jumper_devfull.jpg|On the [[APF9328DevFull]]]]  [[Image:bootstrap_jumper_apf27.jpg|On the [[APF27Dev]]]] [[Image:bootstrap_jumper_apf51.jpg|On the [[APF51Dev]]]]
 * Start the RS232 terminal on the Host side (115200 bauds 8N1)

@@ Line 1: / Line 1: @@
 ==U-Boot communication quick check==
 * Verify that your RS232 cable is correctly connected
-* The [[BootStrap#Introduction|bootstrap jumper]] must be removed as shown on these photos:
+* The [[BootStrap#Introduction|bootstrap jumper]] '''must be removed''' as shown on these photos:
   [[Image:bootstrap_jumper.jpg|On the [[APF9328DevLight]]]]  [[Image:bootstrap_jumper_devfull.jpg|On the [[APF9328DevFull]]]]  [[Image:bootstrap_jumper_apf27.jpg|On the [[APF27Dev]]]]

← Older revision		Revision as of 08:49, 3 March 2009
Line 10:		Line 10:
	The [[Linux_start_screenshot \| screenshot]] hereafter shows what you will see on your Terminal emulator during the target boot:		The [[Linux_start_screenshot \| screenshot]] hereafter shows what you will see on your Terminal emulator during the target boot:
	{{:Linux_start_screenshot}}		{{:Linux_start_screenshot}}
		+
		+	==Testing TFTP==
		+	* Put some files in ''/tftpboot''
		+	* To test it from U-Boot:
		+	<pre class="apf">
		+	BIOS> setenv serverip 192.168.0.2 (the IP address of your tftp server/PC hosting the files to download)
		+	BIOS> tftp ${fileaddr} apf9328-linux.bin
		+	MAC: 00:1e:ac:00:00:01
		+	operating at 100M full duplex mode
		+	TFTP from server 192.168.0.2; our IP address is 192.168.0.10
		+	Filename 'apf9328-linux.bin'.
		+	Load address: 0x8000000
		+	Loading: #################################################################
		+	######################################################
		+	done
		+	Bytes transferred = 1604984 (187d78 hex)
		+	BIOS>
		+	</pre>
		+
		+	A more detailed [[Target_Software_Installation#Configure_U-Boot\|U-Boot configuration is in Setup Basics here]]