Difference between revisions of "SP VISION"
From ArmadeusWiki
(→Introduction) |
m (→On the APF*_Dev) |
||
| (12 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | + | = Introduction = | |
| − | + | ||
| − | + | ||
The SP_Vision board is an extension of [[APF27Dev]] and [[APF51Dev]] with a Spartan6 and two DDR. It is designed for real-time video processing. | The SP_Vision board is an extension of [[APF27Dev]] and [[APF51Dev]] with a Spartan6 and two DDR. It is designed for real-time video processing. | ||
| − | + | = Configure the sp_vision fpga = | |
| − | + | ||
| − | == | + | SP_Vision FPGA configuration is done through APF* FPGA, then to configure the SP_Vision FPGA you will need a configuration virtual component called ''sp_vision_configure'' under the APF*'s onboard FPGA. |
| + | This virtual component is available in [http://periphondemand.git.sourceforge.net/git/gitweb.cgi?p=periphondemand/periphondemand;a=tree;f=src/library/components/sp_vision_configure;h=babdb0b05178267c1a8d077b0a1c5737820dea0e;hb=HEAD POD library], but if you don't want to make special design just for configuration, a standard design is provided in armadeus tree. | ||
| − | == | + | == On the APF*_Dev == |
| − | ''' | + | * First select the driver for sp_vision_configuraton under linux-menuconfig : |
| + | |||
| + | <pre class="host"> | ||
| + | [ ]$ make linux-menuconfig | ||
| + | </pre> | ||
| + | |||
| + | <pre class="config"> | ||
| + | Device Drivers ---> | ||
| + | Armadeus specific drivers ---> | ||
| + | FPGA Drivers ---> | ||
| + | [...] | ||
| + | [*] virtual components | ||
| + | [...] | ||
| + | [*] Board designs | ||
| + | [...] | ||
| + | <M> board driver for sp_vision fpga loader | ||
| + | </pre> | ||
| + | |||
| + | then | ||
| + | <pre class="host"> | ||
| + | [ ]$ make linux | ||
| + | [...] | ||
| + | [ ]$ make | ||
| + | [...] | ||
| + | </pre> | ||
| + | |||
| + | The configuration bitstream can be found under the directory ''firmware/pod_scripts/'' and it's named '''apf27_spvision_loader.bit''' for APF27 and '''apf51_spvision_loader.bin''' for APF51. To configure the second (sp_vision) FPGA, first FPGA on APF* must be configured with this bitstream. | ||
| + | * Configure the first fpga (if you transfer files by nfs): | ||
| + | <pre class="apf"> | ||
| + | # modprobe fpgaloader | ||
| + | </pre> | ||
| + | On APF27: | ||
| + | <pre class="apf"> | ||
| + | # load_fpga apf27_spvision_loader.bit | ||
| + | </pre> | ||
| + | On APF51: | ||
| + | <pre class="apf"> | ||
| + | # load_fpga apf51_spvision_loader.bin | ||
| + | </pre> | ||
| + | |||
| + | * Once the first FPGA configured, just do : | ||
| + | <pre class="apf"> | ||
| + | # modprobe sploader | ||
| + | # modprobe sploader_prober | ||
| + | # dd if=your_sp_vision_bitstream.bit of=/dev/sp_loader | ||
| + | </pre> | ||
| + | |||
| + | = Communicate with sp_vision = | ||
| + | {{Under_Construction}} | ||
Latest revision as of 17:18, 4 September 2013
Contents
Introduction
The SP_Vision board is an extension of APF27Dev and APF51Dev with a Spartan6 and two DDR. It is designed for real-time video processing.
Configure the sp_vision fpga
SP_Vision FPGA configuration is done through APF* FPGA, then to configure the SP_Vision FPGA you will need a configuration virtual component called sp_vision_configure under the APF*'s onboard FPGA. This virtual component is available in POD library, but if you don't want to make special design just for configuration, a standard design is provided in armadeus tree.
On the APF*_Dev
- First select the driver for sp_vision_configuraton under linux-menuconfig :
[ ]$ make linux-menuconfig
Device Drivers --->
Armadeus specific drivers --->
FPGA Drivers --->
[...]
[*] virtual components
[...]
[*] Board designs
[...]
<M> board driver for sp_vision fpga loader
then
[ ]$ make linux [...] [ ]$ make [...]
The configuration bitstream can be found under the directory firmware/pod_scripts/ and it's named apf27_spvision_loader.bit for APF27 and apf51_spvision_loader.bin for APF51. To configure the second (sp_vision) FPGA, first FPGA on APF* must be configured with this bitstream.
- Configure the first fpga (if you transfer files by nfs):
# modprobe fpgaloader
On APF27:
# load_fpga apf27_spvision_loader.bit
On APF51:
# load_fpga apf51_spvision_loader.bin
- Once the first FPGA configured, just do :
# modprobe sploader # modprobe sploader_prober # dd if=your_sp_vision_bitstream.bit of=/dev/sp_loader
Communicate with sp_vision
Page under construction...
Informations on this page are not guaranteed !!
