Difference between revisions of "MCP4912"
From ArmadeusWiki
(→set values) |
m (→Driver) |
||
| (8 intermediate revisions by 3 users not shown) | |||
| Line 1: | Line 1: | ||
| − | =Description= | + | ==Description== |
| − | This 2 channels 10bits [[SPI]] DAC (Digital to Analog Converter) is mounted | + | This 2 channels 10bits [[SPI]] DAC (Digital to Analog Converter) is mounted on the [[APF51Dev]] development boards. |
==Connections== | ==Connections== | ||
| − | On your | + | On your [[APF51Dev]] there are 2 signals to use: |
| − | * DAC_OUTA: corresponds to OUTA (pin 1 of J5 on the APF51Dev). It's the first output. | + | * DAC_OUTA: corresponds to OUTA (pin 1 of J5 on the [[APF51Dev]]). It's the first output. |
| − | * DAC_OUTB: corresponds to OUTB (pin | + | * DAC_OUTB: corresponds to OUTB (pin 3 of J5 on the [[APF51Dev]]). It's the 2nd output. |
| − | The default output voltage range is 0- | + | The default output voltage range is [0-2.5V] on the [[APF51Dev]] (because the 2,5V reference output of the [[AS1531]] is used as reference input for the MCP4912). |
== Driver == | == Driver == | ||
| − | The driver is included in ARMadeus distribution, | + | The driver is included in the ARMadeus distribution, and has to be selected (done by default on [[APF51]]): |
<pre class="host"> | <pre class="host"> | ||
| − | + | $ make linux-menuconfig | |
</pre> | </pre> | ||
| Line 26: | Line 26: | ||
Then compile the distribution : | Then compile the distribution : | ||
<pre class="host"> | <pre class="host"> | ||
| − | + | $ make linux && make | |
</pre> | </pre> | ||
== Use it == | == Use it == | ||
| − | === | + | === Load driver === |
To use the DAC first load module: | To use the DAC first load module: | ||
| Line 37: | Line 37: | ||
</pre> | </pre> | ||
| − | === | + | === Set channel values === |
<pre class="apf"> | <pre class="apf"> | ||
# cd /sys/bus/spi/devices/spi0.1/device0 | # cd /sys/bus/spi/devices/spi0.1/device0 | ||
# ls | # ls | ||
| − | dac_power_mode_0 | + | dac_power_mode_0 dac_trigger_1 power |
| − | dac_power_mode_1 | + | dac_power_mode_1 out0_raw subsystem |
| + | dac_trigger_0 out1_raw uevent | ||
</pre> | </pre> | ||
| − | To set the | + | To set the DAC A channel value to 2.48V (max range) : |
<pre class="apf"> | <pre class="apf"> | ||
| − | # | + | # echo 1023 > out0_raw |
| − | + | </pre> | |
| + | |||
| + | To set the DAC B channel value to 1V : | ||
| + | <pre class="apf"> | ||
| + | # echo 412 > out1_raw | ||
| + | </pre> | ||
| + | |||
| + | === Synchronize channels update === | ||
| + | To have both channels output updated simultaneously (value 2V) when setting the DAC B channel : | ||
| + | <pre class="apf"> | ||
| + | # echo 0 > dac_trigger_0 | ||
| + | # echo 1 > dac_trigger_1 | ||
| + | # echo 825 > out0_raw | ||
| + | # echo 825 > out1_raw | ||
</pre> | </pre> | ||
Latest revision as of 19:39, 4 September 2013
Contents
Description
This 2 channels 10bits SPI DAC (Digital to Analog Converter) is mounted on the APF51Dev development boards.
Connections
On your APF51Dev there are 2 signals to use:
- DAC_OUTA: corresponds to OUTA (pin 1 of J5 on the APF51Dev). It's the first output.
- DAC_OUTB: corresponds to OUTB (pin 3 of J5 on the APF51Dev). It's the 2nd output.
The default output voltage range is [0-2.5V] on the APF51Dev (because the 2,5V reference output of the AS1531 is used as reference input for the MCP4912).
Driver
The driver is included in the ARMadeus distribution, and has to be selected (done by default on APF51):
$ make linux-menuconfig
Device Drivers --->
<*> Staging drivers --->
<*> Industrial I/O support --->
<M> Microchip MCP4902, MCP4912, MCP4922 driver
Then compile the distribution :
$ make linux && make
Use it
Load driver
To use the DAC first load module:
# modprobe mcp49x2
Set channel values
# cd /sys/bus/spi/devices/spi0.1/device0 # ls dac_power_mode_0 dac_trigger_1 power dac_power_mode_1 out0_raw subsystem dac_trigger_0 out1_raw uevent
To set the DAC A channel value to 2.48V (max range) :
# echo 1023 > out0_raw
To set the DAC B channel value to 1V :
# echo 412 > out1_raw
Synchronize channels update
To have both channels output updated simultaneously (value 2V) when setting the DAC B channel :
# echo 0 > dac_trigger_0 # echo 1 > dac_trigger_1 # echo 825 > out0_raw # echo 825 > out1_raw
