Difference between revisions of "MT9M111"
From ArmadeusWiki
(New page: MT9M111 is an xxx 1,3 Mpixels sensor that can be found in the following commercial camera modules: * * ==Connecting the XXX module to the APF27== * ===Description=== * CSI port (8 bit...) |
|||
| (One intermediate revision by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | MT9M111 is an | + | MT9M111 is an Aptina 1,3 Mpixels sensor that can be found in the following commercial camera modules: |
| − | * | + | * http://www.elechouse.com/elechouse/index.php?main_page=product_info&cPath=168_169&products_id=804 |
| − | * | + | * other ? |
==Connecting the XXX module to the APF27== | ==Connecting the XXX module to the APF27== | ||
| Line 12: | Line 12: | ||
===Adaptation board=== | ===Adaptation board=== | ||
| − | * (Preliminary) Schematics and layouts (for [http://kicad.sourceforge.net/wiki/index.php/Main_Page KiCAD]) of an APF27 adaptation board are available [ | + | * (Preliminary) Schematics and layouts (for [http://kicad.sourceforge.net/wiki/index.php/Main_Page KiCAD]) of an APF27 adaptation board are available [here]. |
| − | [[Image: | + | [[Image:MT9M111_adapt.png|center|thumb|600px|]] |
{|border=0 summary="" | {|border=0 summary="" | ||
|--- | |--- | ||
| − | [[Image: | + | [[Image:apf27dev_with_MT9M111_adapt_pluggedin.jpg|thumb|320px|APF27Dev with MT9M111 camera and LCD]] |
|| | || | ||
| − | [[Image: | + | [[Image:MT9M111_adapt_pluggedin.jpg|thumb|320px|MT9M111 montage (I2C cable: Green on J8 pin 8 and Blue on J8 pin 10)]] |
|--- | |--- | ||
|} | |} | ||
Latest revision as of 18:04, 21 January 2014
MT9M111 is an Aptina 1,3 Mpixels sensor that can be found in the following commercial camera modules:
- http://www.elechouse.com/elechouse/index.php?main_page=product_info&cPath=168_169&products_id=804
- other ?
Contents
Connecting the XXX module to the APF27
Description
- CSI port (8 bits data + 4 bits control signals) is used to transmit images. (10 bits mode not usable on i.MX). These signals are available on the APF27Dev J9 connector (2,5V logic).
- I2C bus is used to configure the sensor. This bus is available on the APF27Dev J8 connector.
- Sensor core/IO power supply (2,5V) comes directly from J9 2,5V.
Adaptation board
- (Preliminary) Schematics and layouts (for KiCAD) of an APF27 adaptation board are available [here].
|
File:MT9M111 adapt pluggedin.jpg MT9M111 montage (I2C cable: Green on J8 pin 8 and Blue on J8 pin 10) |
Usage
- Bring module out of powerdown by driving SSI3_TX (pin 30 of port C) & SSI3_CLK (pin 31 of port C) as GPIOs (through GPIOlib):
echo 94 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio94/direction echo 0 > /sys/class/gpio/gpio94/value; usleep 100000 echo 95 > /sys/class/gpio/export echo out > /sys/class/gpio/gpio95/direction echo 0 > /sys/class/gpio/gpio95/value; usleep 100000
- Load corresponding drivers:
# modprobe mx27_camera Linux video capture interface: v2.00 mx27-camera mx27-camera.0: initialising mx27-camera mx27-camera.0: Camera clock frequency: 33250006 mx27-camera mx27-camera.0: Using EMMA # modprobe mt9m111 camera 0-0: Camera driver attached to camera 0 mx27-camera mx27-camera.0: mclk_get_divisor not implemented. Running at max speed camera 0-0: Detected a MT9M11x chip ID 143a camera 0-0: Camera driver detached from camera 0
Test
- You can then use Armadeus "capture" demo tool to get images from the camera.
- First time you will have to set the camera module registers correctly (not done by the driver yet) by using a custom script ov9653_regs.sh available [here]. Here is how to proceed:
# capture & usleep 400000 ; ./ov9653_regs.sh
