Difference between revisions of "Domotic"
(→RS485) |
GuillaumeT (Talk | contribs) (→RS485) |
||
| Line 32: | Line 32: | ||
===RS485=== | ===RS485=== | ||
| − | Wirelless communication is the best way to connect Endpoints and controler. But sometimes wired connexion will be need. We could considerate RS485 connexion. | + | Wirelless communication is the best way to connect Endpoints and controler. But sometimes wired connexion will be need for direct or faster access. We could considerate RS485 connexion. |
| − | With RS485 nom we can | + | With RS485 nom we can connect up to 32 controllers on one bus. |
<strong>Next steps:</strong> | <strong>Next steps:</strong> | ||
* APF with RS485 transceiver with a PIC and the same transceiver. | * APF with RS485 transceiver with a PIC and the same transceiver. | ||
| − | * Needs to connect | + | * Needs to connect APF to a RS485 bus : Linux driver developement? UART driver ? |
* Schematics for connecting a pic to RS485 bus | * Schematics for connecting a pic to RS485 bus | ||
| − | * Specification of the communication | + | * Specification of the communication protocol between APF and endpoint. Application protocol can be share with Zigbee high level protocol or, must we developped new protocol ? |
| − | * Developpment of a small application on the APF and on the | + | * Developpment of a small application on the APF and on the PIC to test communication. |
Revision as of 09:53, 9 July 2007
Contents
Building blocks for your armadeus-based home management system
- Boa (Embedded Webserver)
- GPIO_Driver
- Analog-Digital Converter
- Digital-Analog Converter
- IR_Receiver
- Wireless interface
Domos Project
The domos project aims is to provide a global, low cost and open source solution for home automation.
A first proposition can be found here: [1]
Three developpers are actually registered.
Subprojects:
- Endpoint / controller communication (LS_Link)
- Controller/controller/server communication (HS_Link)
1. LS_Link
Zigbee
A zigbee solution is foreseen for the wireless communication.
A presentation concerning Zigbee can be found here: [2].
This has to be evaluated.
In order to be able to benefit from the complete Zigbee services, two Microchip ICs will be used (PIC18Fxx and the MRF) as the Zigbee stack is provided for free [3].
MRF24J40 Transceiver [4]
Next steps:
- 2 zigbee prototype board with a PIC and the MRF. One will be used for the endpoint and the other will be connected to the APF through the RS232 (TTL) interface.
- Specification of the communication protocol between the APF and the endpoint (datagram based ?). Evalution of the actual solutions.
- Developpment of a small application on the APF side to communicate with the zigbee board by using the communication protocol previously defined.
- test of the Zigbee stack provided by Microchip. A simple programm has to be written. Default Microchip environment has to be used.
RS485
Wirelless communication is the best way to connect Endpoints and controler. But sometimes wired connexion will be need for direct or faster access. We could considerate RS485 connexion. With RS485 nom we can connect up to 32 controllers on one bus.
Next steps:
- APF with RS485 transceiver with a PIC and the same transceiver.
- Needs to connect APF to a RS485 bus : Linux driver developement? UART driver ?
- Schematics for connecting a pic to RS485 bus
- Specification of the communication protocol between APF and endpoint. Application protocol can be share with Zigbee high level protocol or, must we developped new protocol ?
- Developpment of a small application on the APF and on the PIC to test communication.
