Difference between revisions of "TSC2102"
m (→Touchscreen) |
m |
||
| Line 1: | Line 1: | ||
| − | Informations about the hardware interface between the i.MXL and the TSC2102 | + | Informations about the hardware interface between the i.MXL and the TSC2102. |
==Introduction== | ==Introduction== | ||
| − | This chip is a "SMART" 4-Wire Touch Screen Controller with Stereo DAC | + | This chip is a "SMART" 4-Wire Touch Screen Controller with Stereo DAC and HP Amplifier. It is the one used on the DevFull board but anyone should be able to add it to it's DevLight. It's possible too to solder this chip directly on your [[LQ043_Adapt|LQ043 adaptor board]], if you have one. |
| − | == | + | ==Hardware interface with the i.MXL== |
===Touchscreen=== | ===Touchscreen=== | ||
Configuration and data exchange is done through the SPI bus n°2 (SPI2).<br> | Configuration and data exchange is done through the SPI bus n°2 (SPI2).<br> | ||
| − | The SPI 2 port is shared with the LCD interface of the i.MXL. | + | The SPI 2 port is shared with the LCD interface of the i.MXL (these signals are present on the DevLight V2 LCD connector). |
===Audio=== | ===Audio=== | ||
| Line 39: | Line 39: | ||
* [[TSC2102 Linux driver| TSC2102 Linux driver details ]] | * [[TSC2102 Linux driver| TSC2102 Linux driver details ]] | ||
| − | == | + | ==Self-made adapter board== |
For those who would like to test this component before the DevFull release, take a look at this link: http://www.farnell.fr and type '[http://fr.farnell.com/jsp/Supports+CI,+cartes+prototypes+et+protection+antistatique/Cartes+prototypes/ROTH+ELEKTRONIK/RE933-07/displayProduct.jsp?sku=1426186&_requestid=343396 1426186]' as part to search. <br> | For those who would like to test this component before the DevFull release, take a look at this link: http://www.farnell.fr and type '[http://fr.farnell.com/jsp/Supports+CI,+cartes+prototypes+et+protection+antistatique/Cartes+prototypes/ROTH+ELEKTRONIK/RE933-07/displayProduct.jsp?sku=1426186&_requestid=343396 1426186]' as part to search. <br> | ||
This is a small pcb converting a tssop32 to two rows of 2.54mm holes... | This is a small pcb converting a tssop32 to two rows of 2.54mm holes... | ||
Revision as of 18:09, 1 May 2008
Informations about the hardware interface between the i.MXL and the TSC2102.
Contents
Introduction
This chip is a "SMART" 4-Wire Touch Screen Controller with Stereo DAC and HP Amplifier. It is the one used on the DevFull board but anyone should be able to add it to it's DevLight. It's possible too to solder this chip directly on your LQ043 adaptor board, if you have one.
Hardware interface with the i.MXL
Touchscreen
Configuration and data exchange is done through the SPI bus n°2 (SPI2).
The SPI 2 port is shared with the LCD interface of the i.MXL (these signals are present on the DevLight V2 LCD connector).
Audio
Configuration is done through SPI2 bus and audio data exchange through SSIA
Signals
| i.MXL/DevLight | TSC2102 | Functionnality |
|---|---|---|
| SPI2_SCLK/REV | SCLK | SPI clock |
| SPI2_TXD/SPL_SPR | MOSI | SPI MasterOut SlaveIn |
| SPI2_RXD_1/PS | MISO | SPI MasterIn SlaveOut |
| PortB 17/SSI1_TXDAT | SSn | SPI Chip select |
| SPI2_SS/PortD 8/CLS | PINT/DAVn | Interrupt |
| Reset (on Reset switch) | RESETn | Global reset signal |
Remark:
- i.MXL/DevLight SPI Chip Select signals are not used by Linux SPI infrastructure; it needs multiple chip select (one for each chip connected on the bus), and so GPIOs are used for that purpose.
- Chip interrupt is on Port D because Port B has already some and interrupt are shared on the same port.
Drivers
Self-made adapter board
For those who would like to test this component before the DevFull release, take a look at this link: http://www.farnell.fr and type '1426186' as part to search.
This is a small pcb converting a tssop32 to two rows of 2.54mm holes...
ssi test tool
Use special release of tsc2102 driver and imxreg for audio development purpose. available on request -> Jorasse
- Requirements:
TSC2102 mclk: 16MHZ
FS rate: 32KHz
- uboot: Enable register debug from u-boot:
BIOS> mw.l 0x00200008 0
BIOS> mw.l 0x00210008 0
- linux: Load spi/tsc drivers
modprobe spi_imx
modprobe tsc2102
- imxregs: generate ssi signal
Special release of imxregs can generate an audio signal.
just use imxregs with three parameters: imxregs param1 param2 param3
param1 can be 0: triangular signal or 1: sinusoïdal signal.
param2: period of the signal in number of samples per channel.
param3: Signal level coefficient [0.0 .. 1.0].
for example: imregs 1 50 0.15 produces a 300Hz 5v(pk-pk) sinusoid.
- next step: dma transfer
