Difference between revisions of "MultiMediaCard"

Revision as of 19:07, 29 May 2008

Instructions to use the MultiMediaCard (MMC/SD) on your Armadeus board

Introduction

You can use standard MMC/SD/miniSD/microSD cards with your Armadeus board:

• with a DevLight V1 you must have the corresponding connector attached to your development board. and use an adaptor for miniSD and microSD
• with a DevLight V2 you can use the onboard microSD connector
• with a DevFull you can use the MMC/SD onboard connector and an adaptor for miniSD and microSD

All needed drivers are included in standard Armadeus Linux image.

Mounting the MMC/SD

• Just mount the MMC like you will do on your PC, for example (FAT32 formatted card):

# mount -t vfat /dev/mmcblk0p1 /mnt/mmc

• Then, you can access the MMC's files from the /mnt/mmc directory

If you have problems with vfat code page click here

Booting from MMC/SD

When your rootfs is too big to be put on the APF9328 FLASH, you can always use a MMC/SD like a Hard Drive and boot from it. To do that you must have MMC drivers compiled as builtin in your Linux kernel (done by default in standard Armadeus kernel)

• Format your MMC with Ext2 filesystem (booting on FAT is bad :-) ):

[armadeus] $ sudo mkfs.ext2 /dev/sdxx

• Mount your MMC/SD on your Host filesystem (for example in /media/mmc):

[armadeus] $ sudo mkdir -p /media/mmc
[armadeus] $ sudo mount /dev/sdxx /media/mmc

• Then put your rootfs on this MMC/SD: in Buildroot configure rootfs to be tar-ed:

[armadeus] $ make menuconfig

Target filesystem options --->

[armadeus] $ make

and then:

[armadeus] $ sudo tar xvf ./buildroot/binaries/armadeus/rootfs.arm.tar -C /media/mmc
[armadeus] $ sudo umount /media/mmc

• insert the MMC/SD/microSD on your Armadeus board and then in U-Boot use:

BIOS> run mmcboot

• if you want to automatically boot from SD at each startup, replace default bootcmd U-Boot macro:

BIOS> setenv bootcmd run mmcboot
BIOS> saveenv

(default bootcmd is run jffsboot)

Performances

• MMC/SD#Supported_Cards

Troubleshots

VFAT Code Page

If you encounter this message or something like that

Unable to load NLS charset cp437
FAT: codepage cp437 not found

you have to change the right charset for the current file system:

make linux-menuconfig

In Device Drivers->MMC/SD Card support->iMX Support

In FileSystems->Native Language Support you can select the right charset:

ex: NLS ISO 8859-1  (Latin 1; Western European Languages)

Installation (obsolete now because driver is staticly built in default Armadeus kernel)

When you build your kernel image, then modify its configuration:

[armadeus]$ make linux-menuconfig

in Device Drivers->MMC/SD Card support->iMX Support In FileSystems, don't forget to add support for the filesystem you want to use on the MMC and if you activate FAT/VFAT, don't forget to activate Native Language Support (NLS) otherwise you'll get errors like:

Unable to load NLS charset cp437
FAT: codepage cp437 not found

Save your configuration and then rebuild your kernel image:

[armadeus]$ make linux

now you should have following drivers in your kernel source tree:

drivers/mmc/

Copy mmc_core.ko, imxmmc.ko & mmc_block.ko to your target root filessytem in /lib/modules/ or reflash the generated rootfs.

If not already existing then create the MMC block devices:

# mknod /dev/mmcblk0 b 254 0
# mknod /dev/mmcblk0p1 b 254 1

If not already existing then create the mount point (/mnt/mmc):

# mkdir -p /mnt/mmc

The MMC driver is now included inside the Linux kernel (no more a module) but if you want to use it as a module you will have to:

# modprobe imxmmc
# modprobe mmc_block

Links

• http://en.wikipedia.org/wiki/MultiMedia_Card