Difference between revisions of "LQ043 Adapt"
From ArmadeusWiki
m |
m |
||
| Line 13: | Line 13: | ||
| TFT usage || flat cable (1) connected between X12 of the DevFull and X5 of the LCD_Adapt || On the Devlight V1, the LCD port is not prerouted. This means that you have to solder several wire between the vias corresponding to the LCD signals and a free place on the board where you can add a 2x15pins header. Take a look at the Devlight datasheet. You will find a table representing the bottom side of the board. On the board (bottom), you will see a silkscreen indicating the names of each vias. In the LQ043_Adapt datasheet, you will find the pin description of the 2x15 pins connector. Connect (1 to 1) the signals of the LQ043_adapt to the ones of the Devlight.The flat cable (1) is although required || flat cable(1) connected between X5 of the LCD_Adapt and LCD connector of the DevLight [[Image:LQ043_Adapt_to_DevLightV2.jpg|thumb|Connection between DevLight V2 and LQ043]] | | TFT usage || flat cable (1) connected between X12 of the DevFull and X5 of the LCD_Adapt || On the Devlight V1, the LCD port is not prerouted. This means that you have to solder several wire between the vias corresponding to the LCD signals and a free place on the board where you can add a 2x15pins header. Take a look at the Devlight datasheet. You will find a table representing the bottom side of the board. On the board (bottom), you will see a silkscreen indicating the names of each vias. In the LQ043_Adapt datasheet, you will find the pin description of the 2x15 pins connector. Connect (1 to 1) the signals of the LQ043_adapt to the ones of the Devlight.The flat cable (1) is although required || flat cable(1) connected between X5 of the LCD_Adapt and LCD connector of the DevLight [[Image:LQ043_Adapt_to_DevLightV2.jpg|thumb|Connection between DevLight V2 and LQ043]] | ||
|---------------- | |---------------- | ||
| − | | Touchscreen usage || 4 wires cable (2) connected between X2 of the LCD_Adapt and X32 of the DevFull || colspan="2" align="center" | For those who do not have the APF9328Devfull and would like to use a touch panel, a reserved space has been foreseen on the LQ043_adapt board to solder the [[TSC2102]] (U3) and a small regulator ( | + | | Touchscreen usage || 4 wires cable (2) connected between X2 of the LCD_Adapt and X32 of the DevFull || colspan="2" align="center" | For those who do not have the APF9328Devfull and would like to use a touch panel, a reserved space has been foreseen on the LQ043_adapt board to solder the [[TSC2102]] (U3) and a small regulator (LM317/U4) . This avoids developping or buying a dedicated PCB.In that case one more connection is required: |
| − | * connect LQ043 X7 pin 2 (SSI_B5) with DevLight SSI1_TxDAT. No 4 wire cable is required | + | * connect LQ043 X7 pin 2 (SSI_B5) with DevLight SSI1_TxDAT. No 4 wire cable is required. The TSC2102IDA and the LM317LIDR can be purchased or shipped as samples. Take a look at here: http://focus.ti.com/docs/prod/folders/print/tsc2102.html and http://focus.ti.com/docs/prod/folders/print/lm317l.html |
|- | |- | ||
|} | |} | ||
Revision as of 12:54, 23 August 2008
This adaptor board allows you to connect a Sharp's LQ043 LCD to your DevLight or DevFull.
The description, the datasheet and the schematics of can be found here [1]
The following table summarizes the possibilities to connect the LQ043 and the touch panel to your development board.
| APF9328DevFull | APF9328DevLightV1 | APF9328DevLightV2 | |
|---|---|---|---|
| TFT usage | flat cable (1) connected between X12 of the DevFull and X5 of the LCD_Adapt | On the Devlight V1, the LCD port is not prerouted. This means that you have to solder several wire between the vias corresponding to the LCD signals and a free place on the board where you can add a 2x15pins header. Take a look at the Devlight datasheet. You will find a table representing the bottom side of the board. On the board (bottom), you will see a silkscreen indicating the names of each vias. In the LQ043_Adapt datasheet, you will find the pin description of the 2x15 pins connector. Connect (1 to 1) the signals of the LQ043_adapt to the ones of the Devlight.The flat cable (1) is although required | flat cable(1) connected between X5 of the LCD_Adapt and LCD connector of the DevLight |
| Touchscreen usage | 4 wires cable (2) connected between X2 of the LCD_Adapt and X32 of the DevFull | For those who do not have the APF9328Devfull and would like to use a touch panel, a reserved space has been foreseen on the LQ043_adapt board to solder the TSC2102 (U3) and a small regulator (LM317/U4) . This avoids developping or buying a dedicated PCB.In that case one more connection is required:
| |
Contents
(1) Flat cable
A simple flat cable (PC like) can be used to connect the LQ043_Adapt to the APF9328Devfull. If you do not have one a ready to use cable can be found here: http://www.store.armadeus.com/index.php?language=en Align the pins 1 (square via) on both boards together. Do not use long cables.
(2) 4 wires cable
It is a simple one to one 4 wire cables (2.54mm single row headers on both boards: LQ043_adapt and Devfull)
