Difference between revisions of "USB to WiFi adapter"
From ArmadeusWiki
(→Kernel configuration) |
m (→Packages needed) |
||
| Line 32: | Line 32: | ||
To play with WiFi, select these packages in ''make menuconfig'': | To play with WiFi, select these packages in ''make menuconfig'': | ||
* To configure Wlan: | * To configure Wlan: | ||
| − | < | + | <pre class="config"> |
Package Selection for the target ---> | Package Selection for the target ---> | ||
[*] Networking ---> | [*] Networking ---> | ||
[*] wireless tools | [*] wireless tools | ||
| − | </ | + | </pre> |
* To surf on the net: | * To surf on the net: | ||
| − | < | + | <pre class="config"> |
Package Selection for the target ---> | Package Selection for the target ---> | ||
[*] Networking ---> | [*] Networking ---> | ||
[*] links | [*] links | ||
| − | </ | + | </pre> |
After flashing your rootfs and kernel, you can boot the card and configure WiFi. | After flashing your rootfs and kernel, you can boot the card and configure WiFi. | ||
Revision as of 09:12, 4 February 2009
Contents
Tested hardware
Ralink RT2571WF
The WiFi chipset RT2571WF can be found under the D-Link WiFi key DWL-G122. All drivers are included in Linux kernel 2.6.27. But firmware must be downloaded from serialmonkey website at this address.
To use it with APF9328, you need an APF9328DevFull development board (with USB Host).
Kernel configuration
- First, to use a USB dongle, USB Host must be configured. See this page to know how to do with the APF9328DevFull.
- Then, Wireless network must be configured selecting these options in make linux-menuconfig:
[*] Networking support --->
Wireless --->
<*> Generic IEEE 802.11 Networking Stack (mac80211)
- Finally, select the chipset :
Device Drivers --->
[*] Network device support --->
Wireless LAN --->
[*] Wireless LAN (IEEE 802.11)
<M> Ralink driver support
<M> Ralink rt2501/rt73 (USB) support
Packages needed
To play with WiFi, select these packages in make menuconfig:
- To configure Wlan:
Package Selection for the target --->
[*] Networking --->
[*] wireless tools
- To surf on the net:
Package Selection for the target --->
[*] Networking --->
[*] links
After flashing your rootfs and kernel, you can boot the card and configure WiFi.
WiFi configuration
First mount the module:
# modprobe rt73usb
Then copy the firmware named rt73.bin (found in Module directory of rt73-cvs archive) in apf /lib/firmware directory. If /lib/firmware doesn't exist create it.
mkdir -p /lib/firmware tftp -g -r rt73.bin <yourIP> mv rt73.bin /lib/firmware
Your WiFi-module driver is ready, you can now connect the dongle and after go further with the WiFi configuration.
ZyDas zd1212 chipset
- Tested with SMC WUSB-G (which is in the compatibility list)
Configure Linux
$ make linux26-menuconfig
Same as Ralink +
Device Drivers --->
[*] Network device support --->
Wireless LAN --->
<M> ZyDAS ZD1211/ZD1211B USB-wireless support
[*] ZyDAS ZD1211 debugging
Get firmware
- http://zd1211.ath.cx/get-firmware
- copy the archive to your TFTP export directory
Install firmware
# mkdir -p /lib/firmware/zd1211 # cd /lib/firmware/ # tftp -g -r zd1211-firmware-1.4.tar.bz2 192.168.0.17 # bunzip2 zd1211-firmware-1.4.tar.bz2 # tar xf zd1211-firmware-1.4.tar # mv zd1211-firmware zd1211
Launch driver
# modprobe zd1211rw zd1211rw 1-1.1:1.0: phy0 # ifconfig wlan0 up firmware: requesting zd1211/zd1211b_ub firmware: requesting zd1211/zd1211b_uphr
