Difference between revisions of "MultiMediaCard"

Revision as of 23:08, 2 March 2009

Instructions to use the MultiMediaCard (MMC/SD) on your Armadeus board

Introduction

You can use standard MMC/SD/miniSD/microSD cards with your Armadeus board:

• with a DevLight V1, you must have the corresponding connector attached to your development board. and use an adaptor for miniSD and microSD
• with a DevLight V2, you can use the onboard microSD connector
• with an APF9328DevFull, you can use the MMC/SD onboard connector and an adaptor for miniSD and microSD
• with an APF27Dev, you can use the onboard microSD connector

All needed drivers are included in the standard Armadeus Linux image.

Card insertion

You should something like that:

# imx-mmc imx-mmc.0: card inserted
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SD card at address 01b0
mmcblk0: mmc0:01b0 SD512 500224KiB
 mmcblk0: p1

Mounting the MMC/SD

• Just mount the MMC like you will do on your PC, for example (FAT32 formatted card):

# mount -t vfat /dev/mmcblk0p1 /mnt/mmc

• Then, you can access the MMC's files from the /mnt/mmc directory

If you have problems with vfat code page click here

Booting from MMC/SD

When your rootfs is too big to be put on the APF Flash, you can always use a MMC/SD like a Hard Drive and boot from it (this is possible because standard Armadeus kernel is compiled with the MMC driver built in).

Prepare your card

• On your APF board (to avoid to crash your Host HD), create a good partition table:

 # /sbin/fdisk /dev/mmcblk0
 Delete all existing partion with 'd'
 Create a primary partion: 'n' then 'p' then '1'
 Change bootflag to Linux: 't' then '83'
 Save partition table: 'w'
 (To quit without saving: 'm')

• Then, on your PC, format your MMC with Ext2 filesystem (booting on FAT is bad :-) ):

[armadeus] $ sudo mkfs.ext2 /dev/sdX1   (replace X with your MMC reader drive letter, if your Laptop has an integrated
                                          MMC reader then use mmcblk0p1 instead of sdX1)

• Mount your MMC/SD on your Host filesystem (for example in /media/mmc):

[armadeus] $ sudo mkdir -p /media/mmc
[armadeus] $ sudo mount /dev/sdX1 /media/mmc    (replace X with your MMC reader drive letter, if your Laptop has an integrated
                                                  MMC reader then use mmcblk0p1 instead of sdX1)

Put it your rootfs

• Then put your rootfs on this MMC/SD: in Buildroot configure rootfs to be tar-ed (should be done by default).

[armadeus] $ make menuconfig

Target filesystem options  --->

[armadeus] $ make

• and then uncompress the rootfs to the SD card:

[armadeus] $ sudo tar xvf ./buildroot/binaries/apf9328/apf9328-rootfs.arm.tar -C /media/mmc
[armadeus] $ sudo umount /media/mmc

Boot

• insert the MMC/SD/microSD on your Armadeus board and then in U-Boot use:

 BIOS> run mmcboot

• if you want to automatically boot from SD at each startup, replace default bootcmd U-Boot macro:

 BIOS> setenv bootcmd run mmcboot
 BIOS> saveenv

(default bootcmd is run jffsboot)

Performances

• Show tested cards performances

Troubleshots

VFAT Code Page

If you encounter this message (or something similar):

Unable to load NLS charset cp437
FAT: codepage cp437 not found

you have to add the charset to the supported kernel ones:

make linux26-menuconfig

In File systems ---> -*- Native language support ---> you can select the right charset:

ex: NLS ISO 8859-1  (Latin 1; Western European Languages)

Links

• http://en.wikipedia.org/wiki/MultiMedia_Card