Difference between revisions of "ALSA"

From ArmadeusWiki
Jump to: navigation, search
(→‎Setting playback and capture volume)
(→‎First tries)
Line 111: Line 111:
 
# aplay /tmp/foo.wav
 
# aplay /tmp/foo.wav
 
Playing WAVE '/tmp/foo.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono
 
Playing WAVE '/tmp/foo.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono
 +
</pre>
 +
* for a faster and "wider" sampling:
 +
<pre class="apf">
 +
# arecord -f S16_LE -r 16000 /tmp/toto.wav
 +
Recording WAVE '/tmp/toto.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono
 
</pre>
 
</pre>
  

Revision as of 18:23, 29 December 2009

This page will summarize the informations to use ALSA, ie the sound capabilities (Audio In/Audio Out) of your Armadeus board.

Introduction

ALSA stands for Advanced Linux Sound Architecture and provides audio and MIDI functionality to the Linux operating system. Everyone wanting to write portable & state of the art Linux applications dealing with sound should consider using ALSA.
ALSA is composed of a low level part (target specific Linux drivers) and a userspace library (libasound) with a lot of tools (aplay, arecord, alsamixer).

Hardware

On the i.MX family, used on the Armadeus boards, (good quality) sound can be produced that way:

  1. the i.MX is connected to an audio CODEC (like the TSC2102 on the APF9328 or the TSC2101 on the APF27) through one of its SSI interfaces
  2. the i.MX takes PCM data (ALSA format) from memory and send them (through DMA) to the SSI module
  3. this one converts the data to a serial stream of bits in the I2S format (or AC97). That stream is then sent to the CODEC
  4. the stream is converted by the CODEC's DAC to an analog sound

Sound acquisition (on TSC2101 only) is done in the reverse way.

Installation

ALSA is by default installed on the standard Armadeus rootfs. If you want to change the default configuration, you can consult this wiki page.

Usage

  • Load the ALSA drivers:
 # modprobe snd-imx-alsa-tsc2102
 TI TSC210x driver initializing
 TSC210x detected
  • If you want OSS support (optional):
 modprobe snd-pcm-oss
 modprobe snd-mixer-oss
  • If you want MIDI sequencer support (optional):
 modprobe snd-seq
 modprobe snd-seq-device

Loading script

If you want the drivers to be loaded automatically during each boot, you can add a script in /etc/init.d/. For example: 

 # vi /etc/init.d/S60alsa

#!/bin/sh
  
modprobe snd-imx-alsa-tsc2102

 # chmod a+x /etc/init.d/S60alsa

First checks (optionnal)

  • Check if ALSA is running:
 # cat /proc/asound/version
 Advanced Linux Sound Architecture Driver Version 1.0.17.

# aplay -lL
default:CARD=IMX-ALSA
    i.MX+TSC210x audio, i.MX SSI
    Default Audio Device
null
    Discard all samples (playback) or generate zero samples (capture)
**** List of PLAYBACK Hardware Devices ****
card 0: IMX-ALSA [i.MX+TSC210x audio], device 0: i.MX SSI [i.MX SSI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0

or

 # cat /proc/asound/cards
 0 [IMX-ALSA       ]: i.MX - i.MX+TSC210x audio
                      Freescale i.MX with TSC210x codec

Setting playback and capture volume

  • For this work, you can use alsamixer "pseudo graphic" tool:
# alsamixer

Alsamixer.png

  • choose the Item to setup by using <- -> arrow keys (here Master Playback volume is selected)
  • modify its value with up/down arrow keys
  • you can switch View between Playback and Capture settings with TAB key
  • Capture Handset input is by default muted, you can unmute it by pressing the SPACE key when selected
  • when stereo channels are used you can modify individual channel volume with:
    • 'q': left up, 'z': left down
    • 'e': right up, 'c': right down
  • if alsamixer changed your terminal layout after exiting you can get it back with:
# reset

First tries

  • To play a test sound (connect your headset first ;-) ):
 # aplay /usr/share/sounds/alsa/Side_Left.wav
 Playing WAVE '/usr/share/sounds/alsa/Side_Left.wav' : Signed 16 bit Little Endian, Rate 48000 Hz, Mono

Note: the audio file Side_Left.wav can be copied from your Linux host (if not already on your rootfs)

  • To record a test sound (on APF27Dev only) (connect your microphone first ;-) ):
# arecord /tmp/foo.wav
Recording WAVE '/tmp/foo.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono
  • and to replay it after:
# aplay /tmp/foo.wav
Playing WAVE '/tmp/foo.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono
  • for a faster and "wider" sampling:
# arecord -f S16_LE -r 16000 /tmp/toto.wav
Recording WAVE '/tmp/toto.wav' : Signed 16 bit Little Endian, Rate 16000 Hz, Mono

Going further

Now that ALSA is working, you can switch to serious things ;-) ->

ALSA Soc

On the APF boards we are going to use Embedded version of ALSA: ALSA Soc ->

But for the moment only "standard" version is functionnal.

Links

Retrieved from "http://armadeus.org/wiki/index.php?title=ALSA&oldid=7843"