Difference between revisions of "Power management"
From ArmadeusWiki
(→Ethernet) |
SebastienSz (Talk | contribs) (APF27: show menuconfig option to be able to wake the board with the user button) |
||
| (5 intermediate revisions by one other user not shown) | |||
| Line 1: | Line 1: | ||
| − | |||
==APF9328== | ==APF9328== | ||
| Line 29: | Line 28: | ||
{{Note| now done by default in latest apf kernel configs}} | {{Note| now done by default in latest apf kernel configs}} | ||
<pre class="config"> | <pre class="config"> | ||
| − | + | [*] Power management options ---> | |
[*] Power Management support | [*] Power Management support | ||
[*] Power Management Debug Support | [*] Power Management Debug Support | ||
[*] Verbose Power Management debugging | [*] Verbose Power Management debugging | ||
| − | + | [*] Suspend to RAM and standby | |
[ ] Test suspend/resume and wakealarm during bootup | [ ] Test suspend/resume and wakealarm during bootup | ||
| − | + | < > Advanced Power Management Emulation | |
| + | [ ] Use D14 LED of the APF27Dev for suspend signaling | ||
| + | [ ] Use S1 switch of the APF27Dev to resume after a suspend | ||
</pre> | </pre> | ||
| Line 44: | Line 45: | ||
$ make linux-menuconfig | $ make linux-menuconfig | ||
</pre> | </pre> | ||
| − | |||
<pre class="config"> | <pre class="config"> | ||
| − | + | [*] Power management options ---> | |
| + | [*] Power Management support | ||
| + | [*] Power Management Debug Support | ||
| + | [*] Verbose Power Management debugging | ||
| + | [*] Suspend to RAM and standby | ||
| + | [ ] Test suspend/resume and wakealarm during bootup | ||
| + | < > Advanced Power Management Emulation | ||
| + | [ ] Use D14 LED of the APF27Dev for suspend signaling | ||
| + | [*] Use S1 switch of the APF27Dev to resume after a suspend | ||
</pre> | </pre> | ||
| Line 74: | Line 82: | ||
===List available suspend modes=== | ===List available suspend modes=== | ||
| − | + | <pre class="apf"> | |
| − | + | # cat /sys/power/state | |
| + | standby mem | ||
| + | </pre> | ||
===Enter standby mode (i.MX in Doze mode)=== | ===Enter standby mode (i.MX in Doze mode)=== | ||
| − | + | <pre class="apf"> | |
| − | + | # echo standby > /sys/power/state | |
| − | + | PM: Syncing filesystems ... done. | |
| − | + | PM: Preparing system for standby sleep | |
| − | + | Freezing user space processes ... (elapsed 0.00 seconds) done. | |
| − | + | Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done. | |
| − | + | PM: Entering standby sleep | |
| − | + | Suspending console(s) (use no_console_suspend to debug) | |
| − | + | imx-uart imx-uart.0: preparing suspend | |
| − | + | imx-uart imx-uart.2: preparing suspend | |
| − | + | mxc_nand mxc_nand.0: preparing suspend | |
| + | ... | ||
| + | </pre> | ||
===Enter suspend to memory mode (i.MX in Sleep mode)=== | ===Enter suspend to memory mode (i.MX in Sleep mode)=== | ||
| Line 108: | Line 120: | ||
===Debugging suspend/resume=== | ===Debugging suspend/resume=== | ||
* pass '''no_console_suspend''' as boot parameter: | * pass '''no_console_suspend''' as boot parameter: | ||
| − | + | <pre class="apf"> | |
| − | + | BIOS> setenv extrabootargs no_console_suspend | |
| + | BIOS> boot | ||
| + | </pre> | ||
== Known problems == | == Known problems == | ||
* [[APF27]] USB: usb cause system warning : | * [[APF27]] USB: usb cause system warning : | ||
| − | + | <pre class="apf"> | |
| − | + | # echo standby > /sys/power/state | |
| − | + | PM: Syncing filesystems ... done. | |
| − | + | Freezing user space processes ... (elapsed 0.01 seconds) done. | |
| − | + | Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done. | |
| − | + | ___ apf27_pm_suspend | |
| − | + | ___ apf27_pm_resume | |
| − | + | ------------[ cut here ]------------ | |
| − | + | WARNING: at kernel/hrtimer.c:625 hres_timers_resume+0x3c/0x60() | |
| − | + | hres_timers_resume() called with IRQs enabled!Modules linked in: gpio | |
| − | + | [<c002c0d8>] (dump_stack+0x0/0x14) from [<c003c148>] (warn_slowpath+0x70/0x8c) | |
| − | + | [<c003c0d8>] (warn_slowpath+0x0/0x8c) from [<c0055dfc>] (hres_timers_resume+0x3c/0x60) | |
| + | </pre> | ||
==Links== | ==Links== | ||
Latest revision as of 08:35, 1 July 2016
APF9328
APF9328 alone
Power consumption measurements have been done on an APF9328 board.
The results are available in the APF9328 datasheet.
APF9328 connected to a DevLight board
| Functionnality | power needed @ 5V | how to reduce it |
|---|---|---|
| FPGA | xxxmA | don't configure it |
| Ethernet | ifconfig eth0 down | |
| i.MXL (proc + SDRAM + Flash) | ||
| LCD | ||
APF27/APF28/APF51
Linux configuration
 |
Note: now done by default in latest apf kernel configs |
[*] Power management options --->
[*] Power Management support
[*] Power Management Debug Support
[*] Verbose Power Management debugging
[*] Suspend to RAM and standby
[ ] Test suspend/resume and wakealarm during bootup
< > Advanced Power Management Emulation
[ ] Use D14 LED of the APF27Dev for suspend signaling
[ ] Use S1 switch of the APF27Dev to resume after a suspend
For the apf27, power management handling is done in arch/arm/mach-mx2/pm_imx27.c
- if you put the APF27 in suspend mode, it could be interesting to be able to wake it with the "User button":
$ make linux-menuconfig
[*] Power management options --->
[*] Power Management support
[*] Power Management Debug Support
[*] Verbose Power Management debugging
[*] Suspend to RAM and standby
[ ] Test suspend/resume and wakealarm during bootup
< > Advanced Power Management Emulation
[ ] Use D14 LED of the APF27Dev for suspend signaling
[*] Use S1 switch of the APF27Dev to resume after a suspend
- if you put the APF28 in suspend mode, you can use the power button to wake up the board.
To know if driver is launched
# dmesg | grep Power Power Management for Freescale i.MX2x
Ethernet
for the APF27 the fec_old driver currently do not implement CONFIG_PM stuff...
Power-up
# ifconfig eth0 up
Power-down
# ifconfig eth0 down -->> ~ -400 mW
Other devices
Should comply to suspend/resume device drive mechanism.
List available suspend modes
# cat /sys/power/state standby mem
Enter standby mode (i.MX in Doze mode)
# echo standby > /sys/power/state PM: Syncing filesystems ... done. PM: Preparing system for standby sleep Freezing user space processes ... (elapsed 0.00 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done. PM: Entering standby sleep Suspending console(s) (use no_console_suspend to debug) imx-uart imx-uart.0: preparing suspend imx-uart imx-uart.2: preparing suspend mxc_nand mxc_nand.0: preparing suspend ...
Enter suspend to memory mode (i.MX in Sleep mode)
# echo mem > /sys/power/state
only an external interrupt can now wake up the i.MX27
 |
Warning: The mode 'mem' is not implemented in the kernel 2.6.35 for the APF28. please use the 'standby' mode |
Only few interrupts can wake up the i.MX51 from this mode. please check the mx51 reference manual for further information.
Wake up the board from sleep mode
- For the APF28 you can use the power button, any active interrupt or the RTC.
- For the APF27 you will have to use an external interrupt.
- For the APF51 the RTc or an external interrupt can wake up the board.
Debugging suspend/resume
- pass no_console_suspend as boot parameter:
BIOS> setenv extrabootargs no_console_suspend BIOS> boot
Known problems
- APF27 USB: usb cause system warning :
# echo standby > /sys/power/state PM: Syncing filesystems ... done. Freezing user space processes ... (elapsed 0.01 seconds) done. Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done. ___ apf27_pm_suspend ___ apf27_pm_resume ------------[ cut here ]------------ WARNING: at kernel/hrtimer.c:625 hres_timers_resume+0x3c/0x60() hres_timers_resume() called with IRQs enabled!Modules linked in: gpio [<c002c0d8>] (dump_stack+0x0/0x14) from [<c003c148>] (warn_slowpath+0x70/0x8c) [<c003c0d8>] (warn_slowpath+0x0/0x8c) from [<c0055dfc>] (hres_timers_resume+0x3c/0x60)
