Difference between revisions of "Pci debug"
From ArmadeusWiki
(→Links) |
(→Links) |
||
| (4 intermediate revisions by 2 users not shown) | |||
| Line 4: | Line 4: | ||
= Introduction = | = Introduction = | ||
| − | '''pci_debug''' is a | + | '''pci_debug''' is a useful tool meant to access PCIe BARx memory from userspace. |
| − | = Buildroot configuration = | + | == Buildroot configuration == |
| − | + | * Should be done by default on [[APF6_SP]] | |
| − | * | + | * Select pci_debug: |
<pre class="config"> | <pre class="config"> | ||
Target packages ---> | Target packages ---> | ||
| − | + | Hardware handling ---> | |
| − | + | [*] pcidebug | |
| − | + | ||
</pre> | </pre> | ||
| − | * | + | * then rebuild your BSP: |
| − | <pre class=" | + | <pre class="host"> |
| − | + | $ make | |
| − | + | ||
| − | + | ||
</pre> | </pre> | ||
| − | |||
| − | |||
= Using pci_debug = | = Using pci_debug = | ||
| − | * First find your | + | * First find your PCI device name with lspci : |
<pre class="apf"> | <pre class="apf"> | ||
# lspci | # lspci | ||
| Line 33: | Line 28: | ||
01:00.0 Unclassified device [0013]: Altera Corporation Device e001 (rev 01) | 01:00.0 Unclassified device [0013]: Altera Corporation Device e001 (rev 01) | ||
</pre> | </pre> | ||
| − | For example here, we want to access | + | For example here, we want to access Altera PCI device, then name is : '''01:00.0''' |
* Launch pci_debug with the BAR number in option (-b) : | * Launch pci_debug with the BAR number in option (-b) : | ||
| Line 83: | Line 78: | ||
PCI> | PCI> | ||
</pre> | </pre> | ||
| − | |||
= Links = | = Links = | ||
| − | This tool come from an altera [http://www.alteraforum.com/forum/showthread.php?t=35678 forum post], and the archive code can be found [ | + | This tool come from an altera [http://www.alteraforum.com/forum/showthread.php?t=35678 forum post], and the archive code can be found [https://github.com/Martoni/pcie_debug here]. |
Latest revision as of 15:23, 21 April 2021
Introduction
pci_debug is a useful tool meant to access PCIe BARx memory from userspace.
Buildroot configuration
- Should be done by default on APF6_SP
- Select pci_debug:
Target packages --->
Hardware handling --->
[*] pcidebug
- then rebuild your BSP:
$ make
Using pci_debug
- First find your PCI device name with lspci :
# lspci 00:00.0 PCI bridge: Device 16c3:abcd (rev 01) 01:00.0 Unclassified device [0013]: Altera Corporation Device e001 (rev 01)
For example here, we want to access Altera PCI device, then name is : 01:00.0
- Launch pci_debug with the BAR number in option (-b) :
# pci_debug -s 01:00.0 -b0
# ./pci_debug -s 01:00.0 -b0
PCI debug
---------
- accessing BAR0
- region size is 4194304-bytes
- offset into region is 0-bytes
? Help
d[width] addr len Display memory starting from addr
[width]
8 - 8-bit access
16 - 16-bit access
32 - 32-bit access (default)
c[width] addr val Change memory at addr to val
e Print the endian access mode
e[mode] Change the endian access mode
[mode]
b - big-endian (default)
l - little-endian
f[width] addr val len inc Fill memory
addr - start address
val - start value
len - length (in bytes)
inc - increment (defaults to 1)
q Quit
Notes:
1. addr, len, and val are interpreted as hex values
addresses are always byte based
PCI>
- You can then access BAR0 memory on PCI> prompt.
- Reading 0x20 values from address 0 :
PCI> d32 0 20 00000000: 12345678 12345678 12345678 12345678 00000010: 12345678 12345678 12345678 12345678 PCI>
Links
This tool come from an altera forum post, and the archive code can be found here.
