Difference between revisions of "Vivado installation on Linux"
From ArmadeusWiki
(→Requirements) |
(→HS3) |
||
| (5 intermediate revisions by 3 users not shown) | |||
| Line 4: | Line 4: | ||
== Introduction == | == Introduction == | ||
| − | Vivado is the new | + | Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new Xilinx's products. By default no Armadeus board has a new FPGA supported by Vivado, but, with the APF6, we can use Artix7 on a daughter board (or with Xilinx dev-kit), thanks to PCIe, and enjoy this new Xilinx tool. |
| − | This page is a tutorial to install Vivado on | + | This page is a tutorial on how to install Vivado on Debian Linux host computer. |
| − | {{Note| Vivado can't be used with | + | {{Note| Vivado can't be used with Spartan products, it starts with the "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...)}} |
== Installation == | == Installation == | ||
| Line 14: | Line 14: | ||
* unsure that Bash is the default shell: | * unsure that Bash is the default shell: | ||
| + | <pre class="host"> | ||
| + | $ ls -al /bin/sh | ||
| + | lrwxrwxrwx 1 root root 4 févr. 10 14:49 /bin/sh -> bash | ||
| + | </pre> | ||
| + | * otherwise: | ||
<pre class="host"> | <pre class="host"> | ||
$ sudo dpkg-reconfigure dash | $ sudo dpkg-reconfigure dash | ||
| Line 35: | Line 40: | ||
* Fill forms then wait for about 20 minutes | * Fill forms then wait for about 20 minutes | ||
| − | == | + | == Launching Vivado == |
* Go to the installed directory: | * Go to the installed directory: | ||
| Line 50: | Line 55: | ||
<pre class="host"> | <pre class="host"> | ||
/opt/Xilinx/Vivado/2014.4$ ./bin/vivado | /opt/Xilinx/Vivado/2014.4$ ./bin/vivado | ||
| + | </pre> | ||
| + | |||
| + | == JTaG probes == | ||
| + | |||
| + | === HS3 === | ||
| + | |||
| + | Digilent provide a JTAG probe to configure Xilinx FPGA named [https://store.digilentinc.com/jtag-hs3-programming-cable/ HS3]. | ||
| + | |||
| + | Driver script installation is provided by Vivado in following directory : | ||
| + | |||
| + | <pre> | ||
| + | $ cd Xilinx/Vivado/2020.2/data/xicom/cable_drivers/lin64/install_script/install_drivers | ||
| + | </pre> | ||
| + | |||
| + | Should be launched as root to install drivers: | ||
| + | |||
| + | <pre> | ||
| + | sudo ./install_drivers | ||
</pre> | </pre> | ||
Latest revision as of 16:33, 30 June 2021
Contents
Introduction
Vivado is the new FPGA design tool from Xilinx. It replaces ISE and XPS tools for new Xilinx's products. By default no Armadeus board has a new FPGA supported by Vivado, but, with the APF6, we can use Artix7 on a daughter board (or with Xilinx dev-kit), thanks to PCIe, and enjoy this new Xilinx tool. This page is a tutorial on how to install Vivado on Debian Linux host computer.
 |
Note: Vivado can't be used with Spartan products, it starts with the "7" FPGA serie (artix7, virtex7, zynq, kintex7, ...) |
Installation
Requirements
- unsure that Bash is the default shell:
$ ls -al /bin/sh lrwxrwxrwx 1 root root 4 févr. 10 14:49 /bin/sh -> bash
- otherwise:
$ sudo dpkg-reconfigure dash
Download
- Download the file on xilinx website, note that you will need an account (free) to do that.
Xilinx_Vivado_SDK_2014.4_1119_1_Lin64.bin
Launch install
- To launch install simply type :
$ chmod 777 Xilinx_Vivado_SDK_2014.4_1119_1_Lin64.bin $ ./Xilinx_Vivado_SDK_2014.4_1119_1_Lin64.bin
- Fill forms then wait for about 20 minutes
Launching Vivado
- Go to the installed directory:
$ cd /opt/Xilinx/Vivado/2014.4
- Source the architecture shell file:
/opt/Xilinx/Vivado/2014.4$ source settings64.sh
- Then launch it:
/opt/Xilinx/Vivado/2014.4$ ./bin/vivado
JTaG probes
HS3
Digilent provide a JTAG probe to configure Xilinx FPGA named HS3.
Driver script installation is provided by Vivado in following directory :
$ cd Xilinx/Vivado/2020.2/data/xicom/cable_drivers/lin64/install_script/install_drivers
Should be launched as root to install drivers:
sudo ./install_drivers
