Latest revision as of 12:06, 7 November 2018

Page under construction... Informations on this page are not guaranteed !!

Description

The Armadeus System's standard development board/baseboard for the OPOS6UL module, the OPOS6ULDev, can also be used to evaluate OPOS6UL_NANO SoM. For this you will require a SODIMM adapter... and accept some limitations due to the lack of GPIOs on OPOS6UL_NANO modules, compared to OPOS6UL. Consider this usage as temporary, until OPOS6UL_NANO get the development board it deserves... Don't hesitate to do some lobby to Armadeus Systems hardware team ;-)...

Errata

On OPOS6UL_Dev boards with hardware revision <= 1.2, the USB ports won't be powered unless you do an hardware modification. This modification consist of forcing to 3.3V, the 2 signals USB_OTG1_PWR & USB_OTG2_PWR on U3/AP2152 chip.

Resources

Feature list

Note:

You can't use CAN interfaces of OPOS6ULDev. CAN buses might be output on LCD connector but will require an additional PHY.
2nd Ethernet port is not available.
You won't see anything on LCD unless you force LCD Backlight pin to Logic 1.
RPi connector connected buses are different of the ones when using an OPOS6UL SOM.

Audio

S/PDIF: audio in/out
ALSA

Video Out

Video In

Camera interface

User Input

Touchscreen

Wired communication

Wireless communication

Other

Connectors

RPi compatible connector (J3):

Linux GPIO or device	i.M6UL Mux	wiringPi N°	RPi name	Function	J3 Pin	J3 Pin	Function	RPi name	wiringPi N°	i.M6UL Mux	Linux GPIO or device
-				3.3V	1	2	5V				-
i2c-1	UART5_RX_DATA		SDA1	I2C data	3	4	5V				-
i2c-1	UART5_TX_DATA		SCL1	I2C clock	5	6	GND				-
gpio9	GPIO1_IO09__GPIO1_IO09	7	GPIO7	GPIO / AIN9	7	8	UART Tx	TxD		UART2_TX_DATA__UART2_DCE_TX	ttymxc1
				GND	9	10	UART Rx	RxD		UART2_RX_DATA__UART2_DCE_RX	ttymxc1
gpio113	CSI_MCLK__GPIO4_IO17	0	GPIO0	GPIO	11	12	GPIO / AIN8	GPIO1		GPIO1_IO08__GPIO1_IO08	gpio8
gpio114	CSI_PIXCLK__GPIO4_IO18		GPIO2	GPIO	13	14	GND
gpio122	CSI_DATA05__GPIO4_IO26		GPIO3	GPIO	15	16	GPIO	GPIO4	4	CSI_VSYNC__GPIO4_IO19	gpio115
				3,3V	17	18	GPIO	GPIO5	5	CSI_HSYNC__GPIO4_IO20	gpio116
spidev1.x	CSI_DATA02__ECSPI2_MOSI			SPI MOSI	19	20	GND
spidev1.x	CSI_DATA03__ECSPI2_MISO			SPI MISO	21	22	GPIO	GPIO6	6	CSI_DATA07__GPIO4_IO28	gpio124
spidev1.x	CSI_DATA00__ECSPI2_SCLK			SPI CLK	23	24	SPI_CS0			CSI_DATA01__GPIO4_IO22	spidev1.0
				GND	25	26	NC
i2c-0	UART4_RX_DATA__I2C1_SDA			I2C Data	27	28	I2C clock			UART4_TX_DATA__I2C1_SCL	i2c-0
				NC	29	30	GND
				NC	31	32	NC
				NC	33	34	GND
				NC	35	36	NC
				NC	37	38	NC
				GND	39	40	NC

Tested RPi shields/hats

Dragino Lora/GPS HAT... TO BE RETESTED !!!!

Tips

Bootstrap

Bootstrap jumpers are not connected to OPOS6UL_NANO and so not useful with this SoM

U-Boot

Use OPOS6ULDev "User" LED in U-Boot scripts:
- ON:
```
 BIOS> gpio set 3 
```
- OFF:
```
 BIOS> gpio clear 3 
```

Linux

to activate login in Framebuffer console, please uncomment /etc/inittab line 35 this way:

# Set up a getty on LCD
tty1::respawn:/sbin/getty 38400 tty1

Links

RaspberryPi is a registered trademark of RaspberryPi Foundation.

@@ Line 4: / Line 4: @@
 ==Description==
-The Armadeus System's standard development board/baseboard for the [[OPOS6UL]] module, the [[OPOS6ULDev]], can also be used to evaluate [[OPOS6UL_NANO]] SoM. For this you will require a SODIMM adapter... and accept some limitations due to the lack of GPIOs on [[OPOS6UL_NANO]] modules, compared to [[OPOS6UL]]
+The Armadeus System's standard development board/baseboard for the [[OPOS6UL]] module, the [[OPOS6ULDev]], can also be used to evaluate [[OPOS6UL_NANO]] SoM. For this you will require a SODIMM adapter... and accept some limitations due to the lack of GPIOs on [[OPOS6UL_NANO]] modules, compared to [[OPOS6UL]]. Consider this usage as temporary, until [[OPOS6UL_NANO]] get the development board it deserves... Don't hesitate to do some lobby to Armadeus Systems hardware team ;-)...
-[[Image:OPOS6UL_Dev_with_NANO.png]]
+[[Image:OPOS6UL_Dev_with_NANO.jpg]]
 ==Errata==
-* On [[OPOS6UL_Dev]] boards with hardware revision <= 1.1, the USB ports won't be powered unless you do an hardware modification. This modification consist of forcing to 3.3V, the 2 signals USB_OTG1_PWR & USB_OTG2_PWR on U3/AP2152 chip.
+* On [[OPOS6UL_Dev]] boards with hardware revision <= 1.2, the USB ports won't be powered unless you do an hardware modification. This modification consist of forcing to 3.3V, the 2 signals USB_OTG1_PWR & USB_OTG2_PWR on U3/AP2152 chip.
 ==Resources==
@@ Line 17: / Line 17: @@
 ==Feature list==
+{{Note|
+* You can't use CAN interfaces of [[OPOS6ULDev]]. CAN buses might be output on LCD connector but will require an additional PHY.
+* 2nd Ethernet port is not available.
+* You won't see anything on LCD unless you force LCD Backlight pin to Logic 1.
+* RPi connector connected buses are different of the ones when using an OPOS6UL SOM.
+}}
-{| border="0" cellpadding="5" cellspacing="5" summary="Hardware Add-Ons by functionnalities"
+{| border="0" cellpadding="5" cellspacing="5" summary="Hardware add-ons by functionalities"
 |----------------
 |- style="background:#f4f4f4; color:black; -moz-border-radius:18px;"
@@ Line 44: / Line 50: @@
 * [[USB_OTG]]
 * [[USB_Gadget]]
-* [[CAN_bus_Linux_driver|CAN bus]]
 * [[OneWire_GPIO_bus_Master|1-wire]]
@@ Line 61: / Line 66: @@
 ==Connectors==
-* RPi compatible connector:
+* RPi compatible connector (J3):
 {| class="wikitable" border="1" cellpadding="5" summary="RPi compatible connector of OPOS6ULDev with NANO SoM"
 |- style="background:#efefef;"
-! Linux GPIO !! i.M6UL Mux !! wiringPi N° !! RPi name !! Function !! JX Pin !! JX Pin !! Function !! RPi name !! wiringPi N° !! i.M6UL Mux !! Linux GPIO
+! Linux GPIO or device !! i.M6UL Mux !! wiringPi N° !! RPi name !! Function !! J3 Pin !! J3 Pin !! Function !! RPi name !! wiringPi N° !! i.M6UL Mux !! Linux GPIO or device
 |-
 | - ||  ||  || || '''3.3V''' || style="color:yellow;background:black;" align=center | '''1''' || style="color:yellow;background:black;" align=center | '''2''' || '''5V''' || || || || -
 |-
-| - || UART5_RX_DATA || || SDA1 || I2C data|| style="color:yellow;background:black;" align=center | '''3''' || style="color:yellow;background:black;" align=center | '''4''' || '''5V''' || || || || -
+| i2c-1 || UART5_RX_DATA || || SDA1 || I2C data|| style="color:yellow;background:black;" align=center | '''3''' || style="color:yellow;background:black;" align=center | '''4''' || '''5V''' || || || || -
 |-
-| - || UART5_TX_DATA || || SCL1 || I2C clock || style="color:yellow;background:black;" align=center | '''5''' || style="color:yellow;background:black;" align=center  | '''6''' || '''GND''' || || || || -
+| i2c-1 || UART5_TX_DATA || || SCL1 || I2C clock || style="color:yellow;background:black;" align=center | '''5''' || style="color:yellow;background:black;" align=center  | '''6''' || '''GND''' || || || || -
 |-
-| gpio9 || GPIO1_IO09__GPIO1_IO09 || 7 || GPIO7 || GPIO / AIN9 || style="color:yellow;background:black;" align=center | '''7''' || style="color:yellow;background:black;" align=center | '''8''' || UART Tx || TxD || || ||
+| gpio9 || GPIO1_IO09__GPIO1_IO09 || 7 || GPIO7 || GPIO / AIN9 || style="color:yellow;background:black;" align=center | '''7''' || style="color:yellow;background:black;" align=center | '''8''' || UART Tx || TxD || || UART2_TX_DATA__UART2_DCE_TX || ttymxc1
 |-
-| || ||  || || '''GND''' || style="color:yellow;background:black;" align=center | '''9''' || style="color:yellow;background:black;" align=center | '''10''' || UART Rx || RxD  ||  ||  ||
+| || ||  || || '''GND''' || style="color:yellow;background:black;" align=center | '''9''' || style="color:yellow;background:black;" align=center | '''10''' || UART Rx || RxD  ||  || UART2_RX_DATA__UART2_DCE_RX || ttymxc1
 |-
-| gpio24 || UART3_TX_DATA__GPIO1_IO24 || 0 || GPIO0 || GPIO || style="color:yellow;background:black;" align=center | '''11''' || style="color:yellow;background:black;" align=center  | '''12''' || GPIO / AIN8 || GPIO1 || || GPIO1_IO08__GPIO1_IO08 || gpio8
+| gpio113 || CSI_MCLK__GPIO4_IO17 || 0 || GPIO0 || GPIO || style="color:yellow;background:black;" align=center | '''11''' || style="color:yellow;background:black;" align=center  | '''12''' || GPIO / AIN8 || GPIO1 || || GPIO1_IO08__GPIO1_IO08 || gpio8
 |-
-| gpio25 || UART3_RX_DATA__GPIO1_IO25 || || GPIO2 || GPIO || style="color:yellow;background:black;" align=center | '''13''' || style="color:yellow;background:black;" align=center  | '''14''' || '''GND''' || || || ||
+| gpio114 || CSI_PIXCLK__GPIO4_IO18 || || GPIO2 || GPIO || style="color:yellow;background:black;" align=center | '''13''' || style="color:yellow;background:black;" align=center  | '''14''' || '''GND''' || || || ||
 |-
-| gpio96 || NAND_RE_B__GPIO4_IO00 || || GPIO3 || GPIO || style="color:yellow;background:black;" align=center | '''15''' || style="color:yellow;background:black;" align=center  | '''16''' || GPIO || GPIO4 || 4 || UART1_CTS_B__GPIO1_IO18 || gpio18
+| gpio122 || CSI_DATA05__GPIO4_IO26 || || GPIO3 || GPIO || style="color:yellow;background:black;" align=center | '''15''' || style="color:yellow;background:black;" align=center  | '''16''' || GPIO || GPIO4 || 4 || CSI_VSYNC__GPIO4_IO19 || gpio115
 |-
-| || || || || '''3,3V''' || style="color:yellow;background:black;" align=center | '''17''' || style="color:yellow;background:black;" align=center  | '''18''' || GPIO || GPIO5 || 5 || UART1_RTS_B__GPIO1_IO19  || gpio19
+| || || || || '''3,3V''' || style="color:yellow;background:black;" align=center | '''17''' || style="color:yellow;background:black;" align=center  | '''18''' || GPIO || GPIO5 || 5 || CSI_HSYNC__GPIO4_IO20 || gpio116
 |-
-| || || || || SPI MOSI || style="color:yellow;background:black;" align=center | '''19''' || style="color:yellow;background:black;" align=center  | '''20''' || '''GND''' || || || ||
+| spidev1.x || CSI_DATA02__ECSPI2_MOSI || || || SPI MOSI || style="color:yellow;background:black;" align=center | '''19''' || style="color:yellow;background:black;" align=center  | '''20''' || '''GND''' || || || ||
 |-
-| || || || || SPI MISO || style="color:yellow;background:black;" align=center | '''21''' || style="color:yellow;background:black;" align=center  | '''22''' || GPIO || GPIO6 || 6 || NAND_WE_B__GPIO4_IO01 || gpio97
+| spidev1.x || CSI_DATA03__ECSPI2_MISO || || || SPI MISO || style="color:yellow;background:black;" align=center | '''21''' || style="color:yellow;background:black;" align=center  | '''22''' || GPIO || GPIO6 || 6 || CSI_DATA07__GPIO4_IO28 || gpio124
 |-
-| || || || || SPI CLK || style="color:yellow;background:black;" align=center | '''23''' || style="color:yellow;background:black;" align=center  | '''24''' || SPI_CS0 || || || ||
+| spidev1.x || CSI_DATA00__ECSPI2_SCLK || || || SPI CLK || style="color:yellow;background:black;" align=center | '''23''' || style="color:yellow;background:black;" align=center  | '''24''' || SPI_CS0 || || || CSI_DATA01__GPIO4_IO22 || spidev1.0
 |-
-| || || || || '''GND''' || style="color:yellow;background:black;" align=center | '''25''' || style="color:yellow;background:black;" align=center  | '''26''' || SPI_CS1 || || || ||
+| || || || || '''GND''' || style="color:yellow;background:black;" align=center | '''25''' || style="color:yellow;background:black;" align=center  | '''26''' || NC || || || ||
 |-
-| || || || || I2C Data || style="color:yellow;background:black;" align=center | '''27''' || style="color:yellow;background:black;" align=center | '''28''' || I2C clock || || || ||
+| i2c-0 || UART4_RX_DATA__I2C1_SDA || || || I2C Data || style="color:yellow;background:black;" align=center | '''27''' || style="color:yellow;background:black;" align=center | '''28''' || I2C clock || || || UART4_TX_DATA__I2C1_SCL || i2c-0
 |-
-| gpio132 || SNVS_TAMPER4__GPIO5_IO04 || || || GPIO || style="color:yellow;background:black;" align=center | '''29''' || style="color:yellow;background:black;" align=center | '''30''' || '''GND''' || || || ||
+| || || || || NC || style="color:yellow;background:black;" align=center | '''29''' || style="color:yellow;background:black;" align=center | '''30''' || '''GND''' || || || ||
 |-
-| || || || || GPIO || style="color:yellow;background:black;" align=center | '''31''' || style="color:yellow;background:black;" align=center | '''32''' || GPIO || || || SNVS_TAMPER0__GPIO5_IO00 || gpio128
+| || || || || NC || style="color:yellow;background:black;" align=center | '''31''' || style="color:yellow;background:black;" align=center | '''32''' || NC || || || ||
 |-
-| gpio134 || SNVS_TAMPER6__GPIO5_IO06 || || || GPIO || style="color:yellow;background:black;" align=center | '''33''' || style="color:yellow;background:black;" align=center | '''34''' || '''GND''' || || || ||
+| || || || || NC || style="color:yellow;background:black;" align=center | '''33''' || style="color:yellow;background:black;" align=center | '''34''' || '''GND''' || || || ||
 |-
-| gpio135 || SNVS_TAMPER7__GPIO5_IO07 || || || GPIO || style="color:yellow;background:black;" align=center | '''35''' || style="color:yellow;background:black;" align=center | '''36''' || GPIO || || || SNVS_TAMPER3__GPIO5_IO03 || gpio131
+| || || || || NC || style="color:yellow;background:black;" align=center | '''35''' || style="color:yellow;background:black;" align=center | '''36''' || NC || || || ||
 |-
-| || || || || GPIO || style="color:yellow;background:black;" align=center | '''37''' || style="color:yellow;background:black;" align=center | '''38''' || GPIO || || || SNVS_TAMPER2__GPIO5_IO02 || gpio130
+| || || || || NC || style="color:yellow;background:black;" align=center | '''37''' || style="color:yellow;background:black;" align=center | '''38''' || NC || || || ||
 |-
-| || || || || '''GND''' || style="color:yellow;background:black;" align=center | '''39''' || style="color:yellow;background:black;" align=center | '''40''' || GPIO / 1-Wire || || || SNVS_TAMPER1__GPIO5_IO01 || gpio129
+| || || || || '''GND''' || style="color:yellow;background:black;" align=center | '''39''' || style="color:yellow;background:black;" align=center | '''40''' || NC || || || ||
 |}
@@ Line 116: / Line 121: @@
 ===U-Boot===
 * Use OPOS6ULDev "User" LED in U-Boot scripts:
-** ON: <pre class="apf"> BIOS> gpio set 68 </pre>
+** ON: <pre class="apf"> BIOS> gpio set 3 </pre>
-** OFF: <pre class="apf"> BIOS> gpio clear 68 </pre>
+** OFF: <pre class="apf"> BIOS> gpio clear 3 </pre>
 ===Linux===

Difference between revisions of "OPOS6ULDev used with an OPOS6UL NANO"

Latest revision as of 12:06, 7 November 2018

Contents

Description

Errata

Resources

Feature list

Audio

Video Out

Video In

User Input

Wired communication

Wireless communication

Other

Connectors

Tested RPi shields/hats

Tips

Bootstrap

U-Boot

Linux

Links

Navigation menu

Views

Personal tools

Navigation

Support/community

Development

Search

Tools