Difference between revisions of "ISP1761 Linux driver"
From ArmadeusWiki
(ISP1761 is now statically linked with the kernel) |
(→Usage) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 2: | Line 2: | ||
= Compilation = | = Compilation = | ||
| − | + | {{Note|SVN version 978 and higher include the ISP1761 in the default kernel configuration}} | |
* Launch kernel configuration: | * Launch kernel configuration: | ||
| + | <pre class="host"> | ||
$ make linux-menuconfig | $ make linux-menuconfig | ||
| + | </pre> | ||
* Activate USB support in Linux: | * Activate USB support in Linux: | ||
| − | + | <pre class="config"> | |
| − | * and choose ISP1761 controller '''(driver is no more limited to module usage | + | Device Drivers ---> |
| − | + | USB support ---> | |
| + | <*> Support for Host-side USB (static) | ||
| + | </pre> | ||
| + | * and choose ISP1761 controller '''(driver is no more limited to module usage since svn version 978 and higher)''': | ||
| + | <pre class="config"> | ||
| + | Device Drivers ---> | ||
| + | Armadeus specific drivers ---> | ||
| + | <M> isp1761 USB 2.0 Host controller (module) | ||
| + | </pre> | ||
* then, depending on the devices you're planning to plug, you will have to [[USB_Host | add some more USB drivers.]] | * then, depending on the devices you're planning to plug, you will have to [[USB_Host | add some more USB drivers.]] | ||
| − | = Usage = | + | ==Usage== |
| − | + | {{Note|Since SVN version 978 and higher, the ISP1761 driver is statically linked with the kernel. There is no more need to load the drivers at run time. we keep instruction hereafter as general purpose information or in case you prefer to use ISP1761 as module.}} | |
* Three modules have to be loaded in order to get the ISP working. They have to be started in the following order: | * Three modules have to be loaded in order to get the ISP working. They have to be started in the following order: | ||
| + | <pre class="apf"> | ||
# modprobe apf9328-isp1761 | # modprobe apf9328-isp1761 | ||
# modprobe hal_imx | # modprobe hal_imx | ||
# modprobe pehci | # modprobe pehci | ||
| + | </pre> | ||
* or put them in a bash script in /etc/init.d: | * or put them in a bash script in /etc/init.d: | ||
| + | <source lang="bash"> | ||
#!/bin/sh | #!/bin/sh | ||
modprobe apf9328-isp1761 | modprobe apf9328-isp1761 | ||
modprobe hal_imx | modprobe hal_imx | ||
modprobe pehci | modprobe pehci | ||
| + | </source> | ||
* and then you should see (on console): | * and then you should see (on console): | ||
| + | <pre class="apf"> | ||
isp1761 isp1761.0: NXP ISP1761 | isp1761 isp1761.0: NXP ISP1761 | ||
isp1761 isp1761.0: new USB bus registered, assigned bus number 1 | isp1761 isp1761.0: new USB bus registered, assigned bus number 1 | ||
| Line 31: | Line 46: | ||
drivers/armadeus/isp1761/hal/hal_imx.c: Registered Driver ISP1761HCD | drivers/armadeus/isp1761/hal/hal_imx.c: Registered Driver ISP1761HCD | ||
pehci: Host Driver has been Registered | pehci: Host Driver has been Registered | ||
| − | + | usb 1-1: new high speed USB device using isp1761 and address 2 | |
usb 1-1: configuration #1 chosen from 1 choice | usb 1-1: configuration #1 chosen from 1 choice | ||
hub 1-1:1.0: USB hub found | hub 1-1:1.0: USB hub found | ||
hub 1-1:1.0: 3 ports detected | hub 1-1:1.0: 3 ports detected | ||
| + | </pre> | ||
= Performances = | = Performances = | ||
Latest revision as of 14:20, 17 July 2009
This page summarizes the informations to use the DevFull's ISP1761 USB Host controller with Linux. With recent version of Armadeus (svn version 978 or higher ) ISP1761 driver is part of the default configuration. Therefore there is no more need to configure Armadeus to use Host USB controller and the user configuration is now limited to add some more USB drivers.
Contents
Compilation
 |
Note: SVN version 978 and higher include the ISP1761 in the default kernel configuration |
- Launch kernel configuration:
$ make linux-menuconfig
- Activate USB support in Linux:
Device Drivers --->
USB support --->
<*> Support for Host-side USB (static)
- and choose ISP1761 controller (driver is no more limited to module usage since svn version 978 and higher):
Device Drivers --->
Armadeus specific drivers --->
<M> isp1761 USB 2.0 Host controller (module)
- then, depending on the devices you're planning to plug, you will have to add some more USB drivers.
Usage
| |
Note: Since SVN version 978 and higher, the ISP1761 driver is statically linked with the kernel. There is no more need to load the drivers at run time. we keep instruction hereafter as general purpose information or in case you prefer to use ISP1761 as module. |
- Three modules have to be loaded in order to get the ISP working. They have to be started in the following order:
# modprobe apf9328-isp1761 # modprobe hal_imx # modprobe pehci
- or put them in a bash script in /etc/init.d:
#!/bin/sh
modprobe apf9328-isp1761
modprobe hal_imx
modprobe pehci
- and then you should see (on console):
isp1761 isp1761.0: NXP ISP1761 isp1761 isp1761.0: new USB bus registered, assigned bus number 1 isp1761 isp1761.0: irq 138, io mem 0x00000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected drivers/armadeus/isp1761/hal/hal_imx.c: Registered Driver ISP1761HCD pehci: Host Driver has been Registered usb 1-1: new high speed USB device using isp1761 and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 3 ports detected
Performances
A performance test has been performed by means of the usb_perf.sh script.
A high speed USB stick (corsair memory flash voyager) has been used.
Test result (mean values): read -> 2980 kBytes/sec write -> 2095 kBytes/sec
The maximal bandwidth has been also measured by using a scope and by tranferring 4096 bytes from the USBstick to a buffer of a kernel driver
Result: ~10MB/sec
