Difference between revisions of "APF51"
From ArmadeusWiki
(New page: ==Description== The APF51 is a high-end Single Board Computer targeted for advanced GUI, intensive computation and extended connectivity. Here is a list of the main features: * Processor:...) |
|||
| (9 intermediate revisions by 5 users not shown) | |||
| Line 1: | Line 1: | ||
| + | [[Category: APF51]] | ||
==Description== | ==Description== | ||
| − | The APF51 is a high-end Single Board Computer targeted for advanced GUI, intensive computation and extended connectivity. | + | The APF51 is a high-end [https://en.wikipedia.org/wiki/Single-board_computer Single Board Computer] targeted for advanced GUI, intensive computation and extended connectivity. |
Here is a list of the main features: | Here is a list of the main features: | ||
* Processor: [http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX515 Freescale i.MX51] (Cortex-A8 @ 800MHz) | * Processor: [http://www.freescale.com/webapp/sps/site/prod_summary.jsp?code=i.MX515 Freescale i.MX51] (Cortex-A8 @ 800MHz) | ||
| − | * RAM: Mobile DDR. 64 to 512MB. 32 bits data bus. Default capacity will be | + | * RAM: Mobile DDR 400. 64 to 512MB. 32 bits data bus. Default capacity will be 256MB. |
* Flash: Mobile NAND. 512MB, 8 bits data bus. | * Flash: Mobile NAND. 512MB, 8 bits data bus. | ||
* Ethernet: onboard Physical (ready to use Ethernet 10/100Mbit link) | * Ethernet: onboard Physical (ready to use Ethernet 10/100Mbit link) | ||
* USB: High speed USB OTG (OnTheGo) with onboard Physical (ready to use USB OTG link) | * USB: High speed USB OTG (OnTheGo) with onboard Physical (ready to use USB OTG link) | ||
* USB: 2 High speed Hosts with integrated PHY | * USB: 2 High speed Hosts with integrated PHY | ||
| − | + | * FPGA: Xilinx Spartan 6 (LX9 or LX16). Default: LX9 | |
| − | * FPGA: Xilinx Spartan 6 | + | * Touchscreen controler (4/5 wires) |
| − | * Supplies: high end DC/DC converters and LDOs on board. Only one external supply of | + | * Low speed ADCs (up to 4) |
| + | * RTC and Watchdog | ||
| + | * Battery charger (Li-On/Li-Po) | ||
| + | * Supplies: high end DC/DC converters and LDOs on board. Only one external supply of 5V required. | ||
* Low power sleep mode | * Low power sleep mode | ||
| − | * Mechanical dimensions: ~ | + | * Mechanical dimensions: ~58x59mm |
| − | All the i.MX51 peripherals (LCD, 2xSDIO, | + | All the i.MX51 peripherals (LCD, 2xSDIO, 2xSPI, 6xSerial, I2C, CSI, 3xUSB, keypad, PWM, etc...) and the FPGA signals can be accessed through two high density [[Hirose connectors]]. |
==Resources== | ==Resources== | ||
| − | * | + | |
| + | * [[Datasheet | Datasheet and schema]] | ||
==Feature list== | ==Feature list== | ||
| + | * [[APF51_Linux_kernel_status]] | ||
| + | |||
{| border="0" cellpadding="5" cellspacing="5" summary="Hardware Add-Ons by functionnalities" | {| border="0" cellpadding="5" cellspacing="5" summary="Hardware Add-Ons by functionnalities" | ||
|---------------- | |---------------- | ||
| Line 50: | Line 57: | ||
* [[PWM]]: PWM output J2 pin 18 (2.8V output level if used) | * [[PWM]]: PWM output J2 pin 18 (2.8V output level if used) | ||
* [[GPIO_Driver]] | * [[GPIO_Driver]] | ||
| + | * [[APF51_PMIC]] (Touchscreen, RTC, LEDs, GPIOs, ADCs, Battery) | ||
| + | |||
===FPGA=== | ===FPGA=== | ||
* [[Using_FPGA]] | * [[Using_FPGA]] | ||
| + | |} | ||
| + | ==Development boards== | ||
| + | * [[APF51Dev]] | ||
| + | * [[PPS51]] | ||
[[Category:MainBoards]] | [[Category:MainBoards]] | ||
[[Category:Hardware]] | [[Category:Hardware]] | ||
Latest revision as of 08:40, 12 February 2015
Contents
Description
The APF51 is a high-end Single Board Computer targeted for advanced GUI, intensive computation and extended connectivity.
Here is a list of the main features:
- Processor: Freescale i.MX51 (Cortex-A8 @ 800MHz)
- RAM: Mobile DDR 400. 64 to 512MB. 32 bits data bus. Default capacity will be 256MB.
- Flash: Mobile NAND. 512MB, 8 bits data bus.
- Ethernet: onboard Physical (ready to use Ethernet 10/100Mbit link)
- USB: High speed USB OTG (OnTheGo) with onboard Physical (ready to use USB OTG link)
- USB: 2 High speed Hosts with integrated PHY
- FPGA: Xilinx Spartan 6 (LX9 or LX16). Default: LX9
- Touchscreen controler (4/5 wires)
- Low speed ADCs (up to 4)
- RTC and Watchdog
- Battery charger (Li-On/Li-Po)
- Supplies: high end DC/DC converters and LDOs on board. Only one external supply of 5V required.
- Low power sleep mode
- Mechanical dimensions: ~58x59mm
All the i.MX51 peripherals (LCD, 2xSDIO, 2xSPI, 6xSerial, I2C, CSI, 3xUSB, keypad, PWM, etc...) and the FPGA signals can be accessed through two high density Hirose connectors.
Resources
Feature list
VideoVideo OutVideo In |
Wired communicationUser Input |
StorageOther
FPGA |
