Difference between revisions of "IMX6-CycloneV interface description"
From ArmadeusWiki
(→Links) |
(→Simplified view) |
||
| Line 18: | Line 18: | ||
Figure 1 is a simplified view of [[Datasheet#APF6 | APF6 schematics]], signals are : | Figure 1 is a simplified view of [[Datasheet#APF6 | APF6 schematics]], signals are : | ||
| − | * '''PCIE_CLK''': 100Mhz differential pcie clock (PCIE_CLKN and PCIE_CLKP). | + | * '''PCIE_CLK''': '''100Mhz''' differential pcie clock (PCIE_CLKN and PCIE_CLKP). |
* '''PCIE_RX''': Differential receive pcie signal lane0 (PCIE_RXN and PCIE_RXP). | * '''PCIE_RX''': Differential receive pcie signal lane0 (PCIE_RXN and PCIE_RXP). | ||
* '''PCIE_TX''': Differential transmit pcie signal lane0(PCIE_TXN and PCIE_TXP). | * '''PCIE_TX''': Differential transmit pcie signal lane0(PCIE_TXN and PCIE_TXP). | ||
| Line 25: | Line 25: | ||
* '''nperst''': set to vcc. | * '''nperst''': set to vcc. | ||
| − | * '''coreclkout''': 125Mhz (by default) clock generated by quartus hard PCIe ip-core, used to clock design by defaut. | + | * '''coreclkout''': '''125Mhz''' (by default) clock generated by quartus hard PCIe ip-core, used to clock design by defaut. |
== FPGA pinout == | == FPGA pinout == | ||
Revision as of 09:28, 12 February 2015
Page under construction...
Informations on this page are not guaranteed !!
Contents
Introduction
This article describe the bus interface configuration to communicate between i.MX6 processor and CycloneV FPGA. In i.MX6, the bus used to make communication with the FPGA is the PCI express.
PCIe
PCIe used to do the communication between i.MX6 and CycloneV is a Gen1 with one lane. By defaut, Armadeus recommend to use the quartus ip-core Cyclone V Avalon-MM Interface for PCIe.
Simplified view
Figure 1 is a simplified view of APF6 schematics, signals are :
- PCIE_CLK: 100Mhz differential pcie clock (PCIE_CLKN and PCIE_CLKP).
- PCIE_RX: Differential receive pcie signal lane0 (PCIE_RXN and PCIE_RXP).
- PCIE_TX: Differential transmit pcie signal lane0(PCIE_TXN and PCIE_TXP).
- npor: set to Vcc.
- nperst: set to vcc.
- coreclkout: 125Mhz (by default) clock generated by quartus hard PCIe ip-core, used to clock design by defaut.
FPGA pinout
FPGA pinout is the following :
# PCIE_RX set_instance_assignment -name IO_STANDARD "1.5-V PCML" -to hip_serial_rx_in0 set_location_assignment PIN_AA2 -to hip_serial_rx_in0 set_location_assignment PIN_AA1 -to "hip_serial_rx_in0(n)" # PCIE_TX set_instance_assignment -name IO_STANDARD "1.5-V PCML" -to hip_serial_tx_out0 set_location_assignment PIN_Y4 -to hip_serial_tx_out0 set_location_assignment PIN_Y3 -to "hip_serial_tx_out0(n)" # PCIE_CLK set_instance_assignment -name IO_STANDARD "1.5-V PCML" -to refclk_clk set_location_assignment PIN_V4 -to refclk_clk set_location_assignment PIN_U4 -to "refclk_clk(n)" # nperst set_location_assignment PIN_R17 -to nperst # npor set_location_assignment PIN_R16 -to npor
