Difference between revisions of "IMX6-CycloneV interface description"
(→Quartus : Avalon-MM Cyclone V Hard IP for PCI Express configuration) |
(→Transceiver Reconfiguration Controller) |
||
| Line 59: | Line 59: | ||
TODO | TODO | ||
| + | |||
| + | ==== General connexion schematics ==== | ||
| + | |||
| + | [[Image:fpga_cycloneV_qsys_cvp_connexion.png]] | ||
=== FPGA pinout === | === FPGA pinout === | ||
Revision as of 08:16, 22 June 2015
Page under construction...
Informations on this page are not guaranteed !!
Introduction
This article describe the bus interface configuration to communicate between i.MX6 processor and CycloneV FPGA. In i.MX6, the bus used to make communication with the FPGA is the PCI express.
PCIe
PCIe used to do the communication between i.MX6 and CycloneV is a Gen1 with one lane. By defaut, Armadeus recommend to use the quartus ip-core Cyclone V Avalon-MM Interface for PCIe.
Simplified view
Figure 1 is a simplified view of APF6 schematics, signals are :
- PCIE_CLK: 125Mhz differential pcie clock (PCIE_CLKN and PCIE_CLKP).
- PCIE_RX: Differential receive pcie signal lane0 (PCIE_RXN and PCIE_RXP).
- PCIE_TX: Differential transmit pcie signal lane0(PCIE_TXN and PCIE_TXP).
- npor: set to Vcc.
- nperst: set to vcc.
- coreclkout: 125Mhz (by default) clock generated by quartus hard PCIe ip-core, used to clock design by defaut.
Qsys (Quartus) : Avalon-MM Cyclone V Hard IP for PCI Express configuration (CvP)
3 Qsys components are required to use PCIe on apf6sp with configuration via PCIe:
- Avalon-MM Cyclone V Hard IP for PCI Express : The hard ip for PCIe
- Altera PCIe Reconfig Driver
- Transceiver Reconfiguration Controller
Avalon-MM Cyclone V Hard IP for PCI Express
To use the Altera IP on the APF6_SP configure it as following :
- Number of lanes : x1
- Enable configuration via the PCIe link
- BAR0
- Type: 32-bit non-prefetchable memory
- Vendor ID: 0x00001172
- Device ID: 0x0000e001
- Class Code: 0x00001300 (there is a bug in quartus, the actual class code is here 13)
- Maximum payload : 128 bytes (PCIe i.MX6's rootcomplex support only 128bytes payload maximum)
Altera PCIe Reconfig Driver
TODO
Transceiver Reconfiguration Controller
TODO
General connexion schematics
FPGA pinout
FPGA pinout is the following :
# PCIE_RX set_instance_assignment -name IO_STANDARD "1.5-V PCML" -to hip_serial_rx_in0 set_location_assignment PIN_AA2 -to hip_serial_rx_in0 set_location_assignment PIN_AA1 -to "hip_serial_rx_in0(n)" # PCIE_TX set_instance_assignment -name IO_STANDARD "1.5-V PCML" -to hip_serial_tx_out0 set_location_assignment PIN_Y4 -to hip_serial_tx_out0 set_location_assignment PIN_Y3 -to "hip_serial_tx_out0(n)" # PCIE_CLK set_instance_assignment -name IO_STANDARD "1.5-V PCML" -to refclk_clk set_location_assignment PIN_V4 -to refclk_clk set_location_assignment PIN_U4 -to "refclk_clk(n)" # nperst set_location_assignment PIN_R17 -to nperst # npor set_location_assignment PIN_R16 -to npor
Clocking without PCIe
PCIe_clk input can be used to clock the entire design without using the PCIe hard ip-core. But it can't be use directly, PLL must be instancied.
Page under construction...
Informations on this page are not guaranteed !!
