Android
Page under construction...
Informations on this page are not guaranteed !!
This page will sumarize the efforts made to have Android running on the APF boards.
 |
Note: Due to Android requirements (at least an ARM926 core), it is impossible to have it running on the APF9328 |
Contents
Some readings before starting
Prerequisites for Android installation
Install needed software packages
- Install these package for build the kernel image and for format the mmc/µSD card
$ sudo apt-get install uboot-mkimage mtd-utils
- The Armadeus Toolchain, only for Armadeus patches
Update the environment variables
Theses environment variables install the Android and Armadeus folder in our home directory, but of course, it can be placed anywhere!
export ANDROID_SOURCE=~/apf27droid
export ANDROID_SDK=~/android-sdk-linux_x86-1.5_r3
export ARMADEUS=~/armadeus-3.1
export PATH=${PATH}:${ANDROID_SDK}/tools:${ANDROID_SOURCE}/bin
Download Android source
The getting Android source document describes how to set up our local work environment. Follow theses instructions until Installing Repo chapter.
$ mkdir $ANDROID_SOURCE $ cd $ANDROID_SOURCE $ mkdir bin $ curl http://android.git.kernel.org/repo >$ANDROID_SOURCE/bin/repo $ chmod a+x $ANDROID_SOURCE/bin/repo $ repo init -u git://android.git.kernel.org/platform/manifest.git -b android-sdk-1.5_r3 $ repo sync
Since android-sdk-1.5_r3 branch, the Linux kernel isn't with the Android source, We can download it in a compress archive (tar.gz) file with this android-kernel-2.6.29 (about (70Mib) or with git repository (more 300Mib)
$ mkdir $ANDROID_SOURCE/kernel $ cd $ANDROID_SOURCE/kernel $ git clone git://android.git.kernel.org/kernel/common.git android-2.6.29
Linux Kernel 2.6.29
Apply the Armadeus patchset
Before compiling the kernel, we patch the source with the Armadeus patches. In second time, I will give the URL to retrieve Linux 2.6.29.4 patch.
$ $ARMADEUS/buildroot/toolchain/patch-kernel.sh $ANDROID_SOURCE/kernel $ARMADEUS/downloads patch-2.6.29.4.bz2
$ $ARMADEUS/buildroot/toolchain/patch-kernel.sh $ANDROID_SOURCE/kernel $ARMADEUS/buildroot/target/device/armadeus/linux/kernel-patches/2.6.29.4 \*.patch{,.gz,.bz2}
$ mkdir $ANDROID_SOURCE/kernel/drivers/armadeus
$ cp -r $ARMADEUS/target/linux/modules/* $ANDROID_SOURCE/kernel/drivers/armadeus
Android kernel configuration (2.6.29)
$ cp $ARMADEUS/buildroot/target/device/armadeus/apf27/apf27-linux-2.6.29.config $ANDROID_SOURCE/kernel/arch/arm/configs/apf27_android_defconfig $ cd $ANDROID_SOURCE/kernel $ make ARCH=arm mrproper $ make ARCH=arm apf27_android_defconfig $ make ARCH=arm menuconfig
Make sure your kernel boots normally on your board. Then enable some Android specific configuration and make sure that your kernel still boots (with your standard file system).
- Android pmem allocator
Device Drivers --->
[*] Misc devices --->
[*] Android pmem allocator
- Android drivers
Device Drivers --->
[*] Staging drivers --->
[ ] Exclude Staging drivers from being built (NEW)
...
Android --->
[*] Android Drivers
[*] Android Binder IPC Driver
<*> Android log driver
[ ] Android RAM buffer console
[*] Timed output class driver (NEW)
< > Android timed gpio driver (NEW)
[*] Android Low Memory Killer
- Anonymous Shared Memory Subsystem
General setup --->
[*] Enable the Anonymous Shared Memory Subsystem
UBIFS kernel configuration (2.6.29)
Device Drivers --->
<*> Memory Technology Device (MTD) support --->
UBI - Unsorted block images --->
<*> Enable UBI
(4096) UBI wear-leveling threshold
(1) Percentage of reserved eraseblocks for bad eraseblocks handling
[ ] Emulate MTD devices
*** UBI debugging options ***
[ ] UBI debugging
...
File systems --->
[*] Miscellaneous filesystems --->
<*> UBIFS file system support
[ ] Extended attributes support
[ ] Advanced compression options
[ ] Enable debugging
Build Android kernel
$ make ARCH=arm CROSS_COMPILE=$ANDROID_SOURCE/prebuilt/linux-x86/toolchain/arm-eabi-4.2.1/bin/arm-eabi- uImage $ cp $ANDROID_SOURCE/kernel/arch/arm/boot/uImage $TFTPBOOT/apf27-linux.bin
Android
Battery patch
At the beginning, reboot happened over again even though Android logo appeared on board. Result of investigation, we found that battery power was returned with 0 when boot.. Then, we changed to notify full battery to Android by ignoring the information under /sys/class/power_supply so that to prevent the power down by low battery $ANDROID_SOURCE/frameworks/base/services/jni/com_android_server_BatteryService.cpp
- Change the battery service status as TRUE
static void setBooleanField(JNIEnv* env, jobject obj, const char* path, jfieldID fieldID)
{
const int SIZE = 16;
char buf[SIZE];
jboolean value = true; /* change false -> true */
/*!!!comment out!!!
if (readFromFile(path, buf, SIZE) > 0) {
if (buf[0] == '1') {
value = true;
}
}
*/
env->SetBooleanField(obj, fieldID, value);
}
- Change the volume, voltage and temperature of battery. Return 100%.
static void setIntField(JNIEnv* env, jobject obj, const char* path, jfieldID fieldID)
{
const int SIZE = 128;
char buf[SIZE];
jint value = 100; /* change 0 -> 100 */
/*!!!comment out!!!
if (readFromFile(path, buf, SIZE) > 0) {
value = atoi(buf);
}
*/
env->SetIntField(obj, fieldID, value);
}
- Change the battery charged status as full and deterioration status as fair.
static void android_server_BatteryService_update(JNIEnv* env, jobject obj)
{
setBooleanField(env, obj, AC_ONLINE_PATH, gFieldIds.mAcOnline);
setBooleanField(env, obj, USB_ONLINE_PATH, gFieldIds.mUsbOnline);
setBooleanField(env, obj, BATTERY_PRESENT_PATH, gFieldIds.mBatteryPresent);
setIntField(env, obj, BATTERY_CAPACITY_PATH, gFieldIds.mBatteryLevel);
setIntField(env, obj, BATTERY_VOLTAGE_PATH, gFieldIds.mBatteryVoltage);
setIntField(env, obj, BATTERY_TEMPERATURE_PATH, gFieldIds.mBatteryTemperature);
/* Change */
env->SetIntField(obj, gFieldIds.mBatteryStatus, gConstants.statusFull);
env->SetIntField(obj, gFieldIds.mBatteryHealth, gConstants.healthGood);
env->SetObjectField(obj, gFieldIds.mBatteryTechnology, env->NewStringUTF("1"));
/*!!!comment out!!!
const int SIZE = 128;
char buf[SIZE];
if (readFromFile(BATTERY_STATUS_PATH, buf, SIZE) > 0)
env->SetIntField(obj, gFieldIds.mBatteryStatus, getBatteryStatus(buf));
if (readFromFile(BATTERY_HEALTH_PATH, buf, SIZE) > 0)
env->SetIntField(obj, gFieldIds.mBatteryHealth, getBatteryHealth(buf));
if (readFromFile(BATTERY_TECHNOLOGY_PATH, buf, SIZE) > 0)
env->SetObjectField(obj, gFieldIds.mBatteryTechnology, env->NewStringUTF(buf));
*/
}
Audio
| |
Note: Still compilation error |
cd $ANDROID_SOURCE/external git clone git://android.git.kernel.org/platform/external/alsa‐lib.git git clone git://android.git.kernel.org/platform/external/alsa‐utils.git cd $ANDROID_SOURCE/hardware git clone git://android.git.kernel.org/platform/hardware/alsa_sound.git
edit $ANDROID_SOURCE/build/target/board/generic/BoardConfig.mk
# HAVE_HTC_AUDIO_DRIVER := true # BOARD_USES_GENERIC_AUDIO := true BOARD_USES_ALSA_AUDIO := true BUILD_WITH_ALSA_UTILS := true
edit $ANDROID_SOURCE/hardware/alsa_sound/AudioHardwareALSA.cpp and change bufferSize to 8192 in twice StreamDefaults structures
edit $ANDROID_SOURCE/system/core/init/device.c
static struct perms_ devperms[] = {
{ "/dev/null", 0666, AID_ROOT, AID_ROOT, 0 },
...
{ "/dev/qmi1", 0640, AID_RADIO, AID_RADIO, 0 },
{ "/dev/qmi2", 0640, AID_RADIO, AID_RADIO, 0 },
// Add this line
{ "/dev/snd/", 0664, AID_SYSTEM, AID_AUDIO, 1 },
{ NULL, 0, 0, 0, 0 },
};
static void handle_device_event(struct uevent *uevent)
{
char devpath[96];
char *base, *name;
int block;
...
} else if(!strncmp(uevent->subsystem, "mtd", 3)) {
base = "/dev/mtd/";
mkdir(base, 0755);
// add this conditionnal block
} else if(!strncmp(uevent->subsystem, "sound", 5)) {
base = "/dev/snd/";
mkdir(base, 0755);
} else if(!strncmp(uevent->subsystem, "misc", 4) &&
!strncmp(name, "log_", 4)) {
base = "/dev/log/";
mkdir(base, 0755);
name += 4;
} else
base = "/dev/";
}
Audio files
$ mkdir $ANDROID_SOURCE/system/core/rootdir/media $ mkdir $ANDROID_SOURCE/system/core/rootdir/media/audio $ mkdir $ANDROID_SOURCE/system/core/rootdir/media/audio/ui $ mkdir $ANDROID_SOURCE/system/core/rootdir/media/audio/alarms $ mkdir $ANDROID_SOURCE/system/core/rootdir/media/audio/notifications $ mkdir $ANDROID_SOURCE/system/core/rootdir/media/audio/ringtones $ cp $ANDROID_SOURCE/frameworks/base/data/sounds/effects/* $ANDROID_SOURCE/system/core/rootdir/media/audio/ui/ $ cp $ANDROID_SOURCE/frameworks/base/data/sounds/Alarm_* $ANDROID_SOURCE/system/core/rootdir/media/audio/alarms/ $ cp $ANDROID_SOURCE/frameworks/base/data/sounds/notifications/* $ANDROID_SOURCE/system/core/rootdir/media/audio/notifications/ $ cp $ANDROID_SOURCE/frameworks/base/data/sounds/Ring_* $ANDROID_SOURCE/system/core/rootdir/media/audio/ringtones/
Touchscreen
| |
Note: To do!!! |
Change init.rc
Open $ANDROID_SOURCE/system/core/rootdir:
# create basic filesystem structure
...
# Touchscreen section
export TSLIB_CONSOLEDEVICE=none
export TSLIB_FBDEVICE=/dev/fb0
export TSLIB_TSDEVICE=/dev/input/event1
export TSLIB_CALIBFILE=/etc/pointercal
export TSLIB_CONFFILE=/etc/ts.conf
export TSLIB_PLUGINDIR=/lib/ts
export LD_PRELOAD=/lib/libts.so:/lib/ts/pthres.so
...
on boot
Android start up
init.rc
Open $ANDROID_SOURCE/system/core/rootdir, comment the 'mount roofs' in read only mode and 'mount yaffs2' lines like this:
# setup the global environment
export PATH /sbin:/system/sbin:/system/bin:/system/xbin
export LD_LIBRARY_PATH /system/lib
export ANDROID_BOOTLOGO 1
export ANDROID_ROOT /system
export ANDROID_ASSETS /system/app
export ANDROID_DATA /data
export EXTERNAL_STORAGE /sdcard
export BOOTCLASSPATH /system/framework/core.jar:/system/framework/ext.jar:/system/framework/framework.jar:/system/framework/android.policy.jar:/system/framework/services.jar
mount rootfs rootfs / rw remount
# Backward compatibility
symlink /system/etc /etc
# create mountpoints and mount tmpfs on sqlite_stmt_journals
mkdir /sdcard 0000 system system
mkdir /system
mkdir /data 0771 system system
mkdir /cache 0770 system cache
mkdir /sqlite_stmt_journals 01777 root root
mount tmpfs tmpfs /sqlite_stmt_journals size=4m
mount rootfs rootfs / ro remount
write /proc/sys/kernel/panic_on_oops 1
write /proc/sys/kernel/hung_task_timeout_secs 0
write /proc/cpu/alignment 4
write /proc/sys/kernel/sched_latency_ns 10000000
write /proc/sys/kernel/sched_wakeup_granularity_ns 2000000
# mount mtd partitions
# Mount /system rw first to give the filesystem a chance to save a checkpoint
# mount yaffs2 mtd@system /system
# mount yaffs2 mtd@system /system ro remount
setprop EXTERNAL_STORAGE_STATE mounted
mount vfat /dev/block/mmcblk0p1 /sdcard nosuid nodev
# We chown/chmod /data again so because mount is run as root + defaults
mount ext2 /dev/block/mmcblk0p2 /data nosuid nodev
chown system system /data
chmod 0771 /data
# Same reason as /data above
# mount yaffs2 mtd@cache /cache nosuid nodev
chown system cache /cache
chmod 0770 /cache
# This may have been created by the recovery system with odd permissions
chown system system /cache/recovery
chmod 0770 /cache/recovery
Compile
$ cd $ANDROID_SOURCE $ make
Making RootFS
Android Root File system
Android emulator has 3 basic images on tools/lib/images directory.
- ramdisk.img is gziped cpio archive. ramdisk.img is a small partition image that is mounted read-only by the kernel at boot time. It only contains /init and a few config files. It is used to start init which will mount the rest of the system images properly and run the init procedure. A Ramdisk is a standard Linux feature. It is made just for the Android and do special things to start up the Android system.
- system.img is a partition image that will be mounted as / and thus contains all system binaries.
- userdata.img is a partition image that can be mounted as /data and thus contains all application-specific and user-specific data.
Create the Android root filesystem for apf27
Android’s root file system is generated in $ANDROID_SOURCE/out/target/product/generic. We will create a folder containing all Android files images.
$ sudo rm -rf $ANDROID_SOURCE/rootfs/ $ cd $ANDROID_SOURCE/out/target/product/generic $ mkdir $ANDROID_SOURCE/rootfs $ cp -a root/* $ANDROID_SOURCE/rootfs/ $ cp -a system/* $ANDROID_SOURCE/rootfs/system/ $ cd $ANDROID_SOURCE/rootfs $ sudo chown -R root.root . $ sudo chmod -R a+rwX data system
JFFS2 Root file system
Actually, Android should use a file system how support mmap function like yaffs2, ext2 or ubifs. Unfortunaly, U-Boot support only jffs2 or ext2. So we will use ext2 on a µSD for data.
Prepare the MMC/µSD card
We will create two partitions on our mmc/µSD card, The first one will use for Android memory card, the second one will use for Android file system. First connect your card reader to your workstation, with the mmc/µSD card inside. Type the dmesg command to see which device is used by your workstation. Let’s assume that this device is /dev/sdb
$ dmesg ... [ 9145.613954] sdb: sdb1 sdb2 [ 9145.615125] sd 10:0:0:0: [sdc] Attached SCSI removable disk [ 9145.615258] sd 10:0:0:0: Attached scsi generic sg3 type 0
Type the mount command to check your currently mounted partitions. If MMC/SD partitions are mounted, unmount them.
In a terminal edit partitions with fdisk:
sudo fdisk /dev/sdb
Delete any existing partition with the d command.
Now, create the boot partition:
Command (m for help): n
Command action
e extended
p primary partition (1-4)
p
Partition number (1-4): 1
First cylinder (1-495, default 1): 1
Last cylinder, +cylinders or +size{K,M,G} (1-239, default 239): +1G
Change its type to FAT32:
Command (m for help): t Selected partition 1 Hex code (type L to list codes): c Changed system type of partition 1 to c (W95 FAT32 (LBA))
Using the n command again, create a second partition filling up the rest of your card (just accept default values).
Now, format the partitions in your card:
sudo mkfs.vfat -n MemoryCard -F 32 /dev/sdb1 sudo mkfs.ext2 -L data /dev/sdb2
Boot setup
$ sudo mkfs.jffs2 -r -e 0x20000 --pad=0x700000 -n $ANDROID_SOURCE/rootfs -o $TFTPBOOT/apf27-rootfs.arm.jffs2
The last thing left to do is to specify how the board boots Linux.
In the U-boot prompt, make the mmc boot is on second partition of the mmc/µSD card
# setenv addjffsargs 'setenv bootargs ${bootargs} root=/dev/mtdblock4 rootfstype=jffs2 init=/init androidboot.console=ttyS0'
# setenv bootcmd run mmcboot
# saveenv
# run update_kernel
# run update_rootfs
Root file system on APF27 NAND memory
| |
Note: wait the UBIFS integration in the u-boot loader |
Boot setup
The last thing left to do is to specify how the board boots Linux. In the U-boot prompt, make the UBIFS boot.
# setenv addubifsargs 'setenv bootargs ${bootargs} root=/dev/mtdblock4 rootfstype=ubifs init=\init androidboot.console=ttyS0'
# setenv ubifsboot 'setenv bootargs ${console} ${mtdparts};run addubifsargs addipargs; setenv autostart yes;nboot.ubifs A0000000 0 ${kernel_offset}'
# setenv bootcmd run ubifsboot
# saveenv
Debug 'n Test
Trace on the console
Trace with strace
# mount /dev/mmcblk0p2 /mnt/mmc # strace chroot /mnt/mmc /init androidboot.console=ttyS0
Trave with logcat
# mount /dev/mmcblk0p2 /mnt/mmc # chroot /mnt/mmc /init androidboot.console=ttyS0 & # chroot /mnt/mmc /system/bin/logcat
Test with Android emulator
Documentation on Android emulator
$ cd $ANDROID_SOURCE/kernel $ make ARCH=arm goldfish_defconfig $ make ARCH=arm CROSS_COMPILE=$ANDROID_SOURCE/prebuilt/linux-x86/toolchain/arm-eabi-4.2.1/bin/arm-eabi # Create AVD (Android Virtual Device) $ $ANDROID_SDK/tools/android create avd -n APF27-H -t 2 -s 272x480 $ $ANDROID_SDK/tools/android create avd -n APF27-L -t 2 -s 480x272 $ $ANDROID_SOURCE/out/host/linux-x86/bin/emulator -avd APF27-H -sysdir $ANDROID_SOURCE/out/target/product/generic/ -kernel $ANDROID_SOURCE/kernel/arch/arm/boot/zImage -data $ANDROID_SOURCE/out/target/product/generic/userdata.img -ramdisk $ANDROID_SOURCE/out/target/product/generic/ramdisk.img -system $ANDROID_SOURCE/out/target/product/generic/system.img
