EMMC OPOS6UL
From ArmadeusWiki
Contents
OPOS6UL eMMC layout
By default, the 4GB eMMC on OPOS6UL module has 4 physical/hardware partitions:
| Boot0 | Boot1 | RPMB | User Data |
| Name | U-Boot name | Size | Comment |
|---|---|---|---|
| boot0 | mmc dev 0 1 | 4MBytes | U-Boot is installed on this partition |
| boot1 | mmc dev 0 2 | 4MBytes | Not used |
| rpmb | mmc dev 0 3 | 512KBytes | Not used |
| User Data | mmc dev 0 0 | remaining space (~3,7GBytes) | Kernel, device tree and rootfs |
Boot0 partition layout
| . | SPL | IMG | ... | ENV1 | ... | ENV2 | ... |
- Linux device: /dev/mmcblk2boot0
| Offset (blocks) | Offset (bytes) | Size (bytes) | Comment |
|---|---|---|---|
| 0 | 0 | 1 KB (0x400) | Free |
| 0x02 | 1 KB (0x400) | 68 KB | U-Boot SPL (apf6-u-boot.spl) |
| 0x8a | 69 KB (0x11400) | 512 KB | U-Boot IMG (apf6-u-boot.img) |
| Free | |||
| 0x800 (2048) | 1024 KB (0x100000) | 10 KB (0x2800) | U-Boot environment |
| Free | |||
| 0xc00 (3072) | 1536 KB (0x180000) | 10 KB (0x2800) | Redundant U-Boot environment |
| Free |
User Data partition layout
There are 3 partitions on the "User Data" physical partition:
| ... | Failsafe (primary) | Rootfs (logical) | Home/Data (logical) |
| Name | U-Boot device | Linux device | Offset (bytes) | Offset (sectors/blocs) | Size | Comment |
|---|---|---|---|---|---|---|
| MBR | NA | NA | 0 | 0 | 512 bytes (1 block) | Master Boot Record. (Don't touch it :-) ) |
| Failsafe | mmc 0:1 | /dev/mmcblk0p1 | 1M | 2048 | 64MBytes (131072 sectors) | system to restore your board in case of problem |
| Rootfs | mmc 0:5 | /dev/mmcblk0p5 | 135168 (0x21000) | 2GBytes (4194304 sectors) | the rootfs is on this partition (ext4 formatted) | |
| Home/Data | mmc 0:6 | /dev/mmcblk0p6 | 4331520 (0x421800) | Rest of space: ~1,6GBytes (3303424 sectors) | HOME can be stored on this partition (ext4 formatted) |
- By default, when flashed from U-Boot, rootfs and boot are only occupying the size of the .ext4 images used during flashing. If you want to increase the rootfs/boot size to all available free space then, after Linux has booted, use the following commands:
# resize2fs /dev/mmcblk0p5 # for Rootfs
- Or with apf-config command
# apf-config
- in menu:
| 1 Expand Filesystem(s) OS can then use all eMMC/SD space |
Rootfs/Boot will then be extended to all the "Rootfs"/"Boot" eMMC partitions space.
Tips
- Commands to partition User Data from fdisk on Host PC with U-Boot UMS. Check /dev/sdc is your OPOS6UL device otherwise you may destroy your PC partition table !!!:
$ sudo fdisk /dev/sdc n p 1 2048 +64M n e 2 133120 7634943 n l 135168 +2G n 4331520 7634943 w
