OPOS6UL SP Interfaces description

Introduction

This article describe the bus interface communication between the i.MX6UL(L) and the spartan6. In i.MX6UL(L) the bus used to make communication with the FPGA is named EIM for External Interface Module. All description of this bus can be found under the i.MX6UL(L) reference manual in chapter 21 (page 821).

Simplified view

figure 1 - i.MX6UL(L)-Spartan6 bus description

Normal communication between i.MX6UL(L) processor and Spartan6 fpga is done with black following signals :

• EIM_BCLK : Clock
• EIM_DA[15:0]: 16bits data and address bus
• EIM_LBA (ADV): Signal used for data/address muxing
• EIM_RW: Read/Write control signal
• EIM_CS0: Chip select

Gray following signals can be used by EIM (External Interface Memory), but not used in default configuration :

• EIM_EB0: Select byte 0 on bus
• EIM_EB1: Select byte 1 on bus
• OE : Output enable
• EIM_CLK0: second clock (EIM_ACLK)

Blue following signals are used for FPGA configuration from imx. Some EIM (black) signals are also used for it.

• FPGA_INITB: Initialize FPGA
• FPGA_PROGRAM : Program (configure) FPGA
• FPGA_DONE: FPGA configuration is done.

Default configuration on CSx

Clocks

The clock used to clock the FPGA is EIM_BCLK (IO_L1P_CCLK_2(N12) and IO_L29P_GCLK3_2(N8)) and is configured to 99 MHz.

Chip Select

The EIM memory space is mapped into 128 MB total memory space in the processor memory. This memory space begin at address 0x50000000.

Start address	End address	Size	Name
0x5000_0000	0x57FF_FFFF	128 MB	EIM (NOR/SRAM)

The total 128 MB of memory can be divided among the EIM four chip selects. See reference manual of i.MX6ULL for more information.

Timings

Read

• U-Boot: To read one 16 bits value in 0 (0x50000000 in i.MX) do :

BIOS> md.w 50000000 1

• Linux: To read one 16 bits value in 0 (0x50000000 in i.MX) do :

# devmem 0x50000000 16

• Bus timings are following :

Write

• U-Boot: To write one 16 bits value in 0 (0x50000000 in i.MX) do :

BIOS> mw.w 50000000 CAFE

• Linux: To write one 16 bits value in 0 (0x50000000 in i.MX) do :

# devmem 0x50000000 16 0xCAFE

• Bus timings are following :

Pinout

Schematics interfaces is given here :

UCF example for interface generated by POD is given here :

NET "rstgen_syscon00_ext_clk" LOC="N8" | IOSTANDARD=LVCMOS33; # EIM_BCLK
NET "rstgen_syscon00_ext_clk" TNM_NET = "rstgen_syscon00_ext_clk";
TIMESPEC "TS_rstgen_syscon00_ext_clk" = PERIOD "rstgen_syscon00_ext_clk" 10.101 ns HIGH 50 %;
NET "imx6ul_wb16_wrapper00_imx_da<0>" LOC="P11" | IOSTANDARD=LVCMOS33; # EIM_DA0
NET "imx6ul_wb16_wrapper00_imx_cs_n" LOC="R11" | IOSTANDARD=LVCMOS33; # EIM_CS0
NET "imx6ul_wb16_wrapper00_imx_da<1>" LOC="M11" | IOSTANDARD=LVCMOS33; # EIM_DA1
NET "imx6ul_wb16_wrapper00_imx_da<2>" LOC="N11" | IOSTANDARD=LVCMOS33; # EIM_DA2
NET "imx6ul_wb16_wrapper00_imx_da<10>" LOC="R10" | IOSTANDARD=LVCMOS33; # EIM_DA10
NET "imx6ul_wb16_wrapper00_imx_da<11>" LOC="L9" | IOSTANDARD=LVCMOS33; # EIM_DA11
NET "imx6ul_wb16_wrapper00_imx_da<12>" LOC="M10" | IOSTANDARD=LVCMOS33; # EIM_DA12
NET "imx6ul_wb16_wrapper00_imx_da<13>" LOC="M8" | IOSTANDARD=LVCMOS33; # EIM_DA13
NET "imx6ul_wb16_wrapper00_imx_da<14>" LOC="K8" | IOSTANDARD=LVCMOS33; # EIM_DA14
NET "imx6ul_wb16_wrapper00_imx_da<15>" LOC="L8" | IOSTANDARD=LVCMOS33; # EIM_DA15
NET "imx6ul_wb16_wrapper00_imx_adv" LOC="R7" | IOSTANDARD=LVCMOS33; # EIM_LBA
NET "imx6ul_wb16_wrapper00_imx_da<7>" LOC="N6" | IOSTANDARD=LVCMOS33; # EIM_DA7
NET "imx6ul_wb16_wrapper00_imx_rw" LOC="R6" | IOSTANDARD=LVCMOS33; # EIM_RW
NET "imx6ul_wb16_wrapper00_imx_da<3>" LOC="P5" | IOSTANDARD=LVCMOS33; # EIM_DA3
NET "imx6ul_wb16_wrapper00_imx_da<4>" LOC="R5" | IOSTANDARD=LVCMOS33; # EIM_DA4
NET "imx6ul_wb16_wrapper00_imx_da<5>" LOC="L6" | IOSTANDARD=LVCMOS33; # EIM_DA5
NET "imx6ul_wb16_wrapper00_imx_da<6>" LOC="L5" | IOSTANDARD=LVCMOS33; # EIM_DA6
NET "imx6ul_wb16_wrapper00_imx_da<8>" LOC="M5" | IOSTANDARD=LVCMOS33; # EIM_DA8
NET "imx6ul_wb16_wrapper00_imx_da<9>" LOC="N5" | IOSTANDARD=LVCMOS33; # EIM_DA9
NET "irq_mngr00_gls_irq" LOC="P3" | IOSTANDARD=LVCMOS33; # FPGA_INITB

FPGA Interrupt

To generate an IRQ from the FPGA to the i.MX, the pin FPGA_INITB is used by default. It correspond to GPIO4_IO16 on i.MX.

Links

• i.MX6UL(L) reference manual (PDF chapter 21 page 821)
• i.MX6UL(L) Datasheet (PDF)
• Spartan6 configuration (PDF)
• Peripheral On Demand configuration files

<< FPGA general page