MultiMediaCard

Instructions to use the MultiMediaCard (MMC/SD) on your Armadeus board

Introduction

You can use standard MMC/SD/miniSD/microSD cards with your Armadeus board:

• with a DevLight V1, you must have the corresponding connector attached to your development board. and use an adaptor for miniSD and microSD
• with a DevLight V2, you can use the onboard microSD connector
• with an APF9328DevFull, you can use the MMC/SD onboard connector and an adaptor for miniSD and microSD
• with an APF27Dev, you can use the onboard microSD connector

All needed drivers are included in the standard Armadeus Linux image.

Card insertion

You should something like that on the Linux console:

 # imx-mmc imx-mmc.0: card inserted
 mmc0: host does not support reading read-only switch. assuming write-enable.
 mmc0: new SD card at address 01b0
 mmcblk0: mmc0:01b0 SD512 500224KiB
  mmcblk0: p1

Mounting the MMC/SD

• Just mount the MMC like you will do on your PC, for example (FAT32 formatted card):

 # mount -t vfat /dev/mmcblk0p1 /mnt/mmc

• Then, you can access the MMC's files from the /mnt/mmc directory

If you have problems with vfat code page click here

Booting from MMC/SD

When your rootfs is too big to be put on the APF Flash, you can always use a MMC/SD like a Hard Drive and boot from it (this is possible because standard Armadeus kernel is compiled with the MMC driver built in).

Prepare your card

• On your APF board (to avoid to crash your Host HD), create a good partition table:

 # /sbin/fdisk /dev/mmcblk0
 Delete all existing partion with 'd'
 Create a primary partion: 'n' then 'p' then '1'
 Change bootflag to Linux: 't' then '83'
 Save partition table: 'w'
 (To quit without saving: 'm')

• Then, on your PC, format your MMC with Ext2 filesystem (booting on FAT is bad :-) ):

 $ sudo mkfs.ext2 /dev/sdX1   (replace X with your MMC reader drive letter, if your Laptop has an integrated
                                           MMC reader then use mmcblk0p1 instead of sdX1)

• If not automatically detected/mounted by your distribution, mount your MMC/SD on your Host filesystem (for example in /media/mmc):

 $ sudo mkdir -p /media/mmc
 $ sudo mount /dev/sdX1 /media/mmc    (replace X with your MMC reader drive letter, if your Laptop has an integrated
                                                   MMC reader then use mmcblk0p1 instead of sdX1)

Put it your rootfs

• Then put your rootfs on this MMC/SD: in Buildroot configure rootfs to be tar-ed (should be done by default).

[armadeus] $ make menuconfig

Target filesystem options  --->

[armadeus] $ make

• and then uncompress the rootfs to the SD card:

[armadeus] $ sudo tar xvf ./buildroot/binaries/apf9328/apf9328-rootfs.arm.tar -C /media/mmc
[armadeus] $ sudo umount /media/mmc

Boot

• insert the MMC/SD/microSD on your Armadeus board and then in U-Boot use:

 BIOS> run mmcboot

• if you want to automatically boot from SD at each startup, replace default bootcmd U-Boot macro:

 BIOS> setenv bootcmd run mmcboot
 BIOS> saveenv

(default bootcmd is run jffsboot)

Performances

• Show tested cards performances

Troubleshots

VFAT Code Page

If you encounter this message (or something similar):

Unable to load NLS charset cp437
FAT: codepage cp437 not found

you have to add the charset to the supported kernel ones:

$ make linux26-menuconfig

File systems  ---> 
    -*- Native language support  --->
        <*>   Codepage 437 (United States, Canada)
        ...
        <*>   NLS ISO 8859-1  (Latin 1; Western European Languages)
        ...

Links

• http://en.wikipedia.org/wiki/MultiMedia_Card

Other languages:
English  •  Français