QEMU

From ArmadeusWiki
Revision as of 15:22, 19 August 2011 by DenisB (Talk | contribs) (→‎Launch it: I tested it with rw, it could write on the disk; the result could be displayed with remounting the armadeus image under the native (x86) system)

Jump to: navigation, search

Page under construction... Construction.png Informations on this page are not guaranteed !!

Well, you don't have enough money to buy an Armadeus board and just want to be part of the "Software" side of the project ? Then QEMU can be a good choice for you !!

Warning Warning:

Just be aware that currently Armadeus hardware is not emulated under QEMU, we are just using an other board hardware emulation (ARM Versatile) and Linux kernel to launch our rootfs and test our software which is not hardware related (ie User interface, Network, etc...)


In order to build a hardware matching machine for Armadeus boards under Qemu, follow this link and add devices you are interested to see emulated in Qemu: Qemu machine development

Installation

  • on Debian, *Ubuntu just do a:
[armadeus]$ sudo apt-get install qemu bridge-utils vde
  • on Kubuntu 9.10 do:
[armadeus]$ sudo apt-get install qemu bridge-utils qemu-kvm-extras vde

Configuration

QEMU has several ways of emulating the network:

  • user mode (by default): you can access Internet from your emulated target or an internal Samba/TFTP server but your are not directly accessible
  • bridge mode: you can communicate directly with the Host


Note Note: For a first try you can skip following part and go directly here.

As we want to mimic the devt environment with a real target (that has its own IP adress and is eccesible from the host) we will use "bridged mode". This mode require some configuration on your Host:

  • Install bridge_utils package
  • Activate IPv4 forwarding, for example on Ubuntu, uncomment the following line in /etc/sysctl.conf:
 $ sudo vim /etc/sysctl.conf
 
   # Uncomment the next line to enable packet forwarding for IPv4
   #net/ipv4/ip_forward=1
  • In /etc/network/interface comment the line referring to your current Ethernet card and replace them with:
auto br0
iface br0 inet dhcp
 bridge_ports eth0
 bridge_fd 9
 bridge_hello 2
 bridge_maxage 12
 bridge_stp off 

#auto eth0
#iface eth0 inet dhcp
Note Note: If you are using a modern linux distribution like Ubuntu, also be sure NetworkManager is disabled/not configured. Otherwise conflict occur and network does not work at all.


  • Create a script /etc/qemu-ifup that will be executed upon the start of QEMU:
#!/bin/sh
echo "Executing /etc/qemu-ifup"
echo "Bringing up $1 for bridged mode..."
sudo /sbin/ifconfig $1 0.0.0.0 promisc up
echo "Adding $1 to br0..."
sudo /usr/sbin/brctl addif br0 $1
sleep 2
  • Now you can append the following options to the qemu command line:
-net nic,vlan=0,macaddr=00:16:3e:00:00:01 -net tap,vlan=0,ifname=tap0,script=/etc/qemu-ifup

You don't need to give a MAC address if you are emulating only one machine, as QEMU will use a default one. However if you have more than one emulated machine (don't forget QEMU can also emulate other architectures than ARM), you will have to specify a unique MAC address for each machine.

  • Once booted, on your guest you can configure the network simply as follows:
 # udhcpc -i eth0

Get/generate simulation images (Linux & rootfs)

  • As QEMU doesn't support (yet) the APF, we will use the Versatile PB emulated hardware. To get a compatible Linux kernel for this board do:
 $ cd your_armadeus_view/
 $ wget ftp://ftp2.armadeus.com/armadeusw/download/qemu/vmlinuz-2.6.29.6-versatile-armadeus

one wanting to rebuild this image itself will find the correspondig config file in the same dir. (after compiling, take arch/arm/boot/zImage)

  • get some useful environment variables:
 $ make shell_env
 $ source armadeus_env.sh
  • deactivate login on serial port:
    • in Buildroot menuconfig:
System configuration  --->
    () Port to run a getty (login prompt) on
* and in $ARMADEUS_ROOTFS_DIR/etc/inittab, comment following lines:
# Put a getty on the serial port
ttymxcX::respawn:/sbin/getty -L ttymxcX 115200 vt100 # GENERIC_SERIAL
  • Re-generate your Armadeus rootfs:
 $ make
  • check the size of your rootfs image
$ ls -al $ARMADEUS_ROOTFS_TAR
  • generate a dummy image larger than your rootfs; here 60 MBytes for a 45 MBytes tared rootfs:
$ dd if=/dev/zero of=armadeus-qemu.img bs=1MB count=60
$ sudo mke2fs -F -m 0 -b 1024 armadeus-qemu.img
  • mount it and copy it your rootfs:
$ mkdir qemu_mnt
$ sudo mount -t ext2 -o loop armadeus-qemu.img qemu_mnt/
$ sudo tar xf $ARMADEUS_ROOTFS_TAR -C qemu_mnt/
$ sudo umount qemu_mnt/
  • now you have all you need to launch Qemu

Launch it

  • Example with 64 MBytes of RAM:
$ qemu-system-arm -M versatilepb -kernel ./vmlinuz-2.6.29.6-versatile-armadeus -hda armadeus-qemu.img -m 64 \
                                -append "root=/dev/sda mem=64M ro"       (rw for read/write works, too instead of tw two last characters ro)

option -cpu arm926 can be added on APF27
Qemu apf ramdisk.png

  • When system has booted, if you are French, load a usable keymap:
 # loadkmap < /etc/i18n/fr.kmap

    =>    loqdk,qp < !etc!i&_n!fr:k,qp    on your PC keyboard

To Be Continued... ;-)

Links

Retrieved from "http://armadeus.org/wiki/index.php?title=QEMU&oldid=9991"