Search results

Create the page "Power" on this wiki! See also the search results found.

Page title matches

Page text matches

• C38A
  ...lt on C38A kit, all power supplies are connected to 5V. To provide 3.3V on power IO (DOVDD):
  3 KB (477 words) - 18:38, 8 April 2010
• Armadeus 3
  Do not forget to save your changes in FLASH, to have them available at next power up:
  20 KB (2,829 words) - 14:12, 30 June 2022
• WiFi
  Tx-Power=0 dBm Power Management:off
  7 KB (911 words) - 15:24, 30 January 2024
• Audio analog connection
  ...voltage presents normally a quiescent DC voltage of approximately half the power supply. ** the power supply (AC adaptor) itself
  3 KB (483 words) - 19:07, 31 July 2011
• APF27Dev
  ** Consequence: the AD9889 can no more be placed in low power mode by hardware.
  2 KB (246 words) - 14:53, 19 March 2021
• Simple blinking LED
  {{Note| Don't forget to power the FPGA IO bank as explained in [[datasheet]]}}
  4 KB (678 words) - 15:24, 25 November 2021
• JTAG
  ...h FPGA, the FPGA chip MUST be powered before using JTAG. Indeed, at system power-up, FPGA is low powered by cutting down the VCCAUX and VCCINT supplies unt Power the board.
  26 KB (3,781 words) - 18:23, 3 June 2016
• OV9653
  * Sensor core power supply (1,8V) is derived from 2,8V of J9.
  4 KB (607 words) - 15:59, 21 January 2014
• APF Enclosure
  ...artment below the base (and probably a battery controller to switch to low-power or shut down the system on low voltage)
  1 KB (211 words) - 23:34, 3 June 2009
• Wiki/Project changes
  ** [[APF28_PMIC|detail the capabilities of APF28's PMIC (Power Management IC)]] ..._battery_pack_for_your_APF|A new page]] has been created to explain how to power on your APF with rechargeable batteries
  34 KB (4,583 words) - 15:35, 17 March 2015
• Beginner's tutorial step 3
  We will now power on your board. Check that your power supply is compatible with the following: * Plug your power supply
  574 bytes (81 words) - 11:14, 16 May 2009
• Android
  ===Power management configuration=== Power management options --->
  23 KB (3,286 words) - 15:28, 3 November 2011
• Bluetooth
  * Power on the chip. [bluetooth]# power on
  19 KB (2,734 words) - 10:34, 7 December 2020
• GSM/GPRS
  ...n't forget to put "Wireless" J42 jumper (near microSD connector) '''AND''' power on FPGA Bank 3 (with corresponding J39 jumper).}} * Power up the chip. (GSM_PWR_EN is connected to the GPIO7_13)
  15 KB (2,358 words) - 15:23, 17 August 2023
• Build your own battery pack for your APF
  If you want to build mobile systems, you can power on your APF with a self made rechargeable battery pack. * a power supply connector. Example: [http://www.selectronic.fr/article.asp?article_r
  709 bytes (103 words) - 10:18, 17 September 2010
• BQ27x00
  <M> Power supply class support ---> [[Category:Power]]
  1 KB (204 words) - 18:08, 4 September 2013
• MAX9768
  * Power on the IC:
  1 KB (177 words) - 18:09, 4 September 2013
• Light-APF27Dev
  * 1 power circuit
  960 bytes (152 words) - 11:15, 14 December 2009
• WPA supplicant
  Bit Rate=24 Mb/s Tx-Power=20 dBm Power Management:on
  6 KB (822 words) - 23:33, 4 May 2023
• ELDER Project
  * '''Sebastien''': Mechanical design, Power Board, Daughter board, GUI: [http://syoctax.free.fr/Elder/Elder_report_seb. **5V and 12V power supply
  24 KB (3,993 words) - 12:24, 30 June 2010

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)